Swisscom TV 2.0 Handbuch Seite 65

ALUPROFILE HOCH UND FLACH MIT KUNSTSTOFFEINSATZ FÜR STRIPBREITE BIS 12MM
Aluminiumstrangguss eloxiert, galvanisch behandelt, nicht leitend, ideal als zusätzlicher Kühlkörper für LED-Strips,
mit Kunststoffeinsatz opal
ZUBEHÖR ALUPROFILE
69524/SET
für Profil hoch
2 Stk. Endkappen + 4 Schrauben
Bestell­Nr.
69524/SET
69570/SET
1 Stk. Verbinder
aus Metall
inkl. Madenschrauben
Bestell­Nr.
69570/SET
PROFILE PROFI FÜR LED-STRIPS
Aufbauprofil hoch
Bestell­Nr. Länge in mm
69521/100 1000mm
69521/200 2000mm
69521/300 3000mm
Aufbauprofil flach
Bestell­Nr. Länge in mm
69522/100 1000mm
69522/200 2000mm
69522/300 3000mm
69527/SET
für Profil flach
2 Stk. Endkappen + 4 Schrauben
Bestell­Nr.
69527/SET
69590/SET
2 Stk. Halteklammern
schwenkbar
inkl. Schrauben
Bestell­Nr.
69590/SET
18,4
15
13,4
19,7
8
18,4
15
13,4
13
2,2
69528/SET
2 Stk. Halteklammern
inkl. Schrauben
Bestell­Nr.
69528/SET
PCBA Mini Dimmer
Model: 43LED/589
43LED/589
Feature
43LED/589 is mini touch sensor dimmer&switch, well matched LED aluminum profiles to use.
Minidimmer für Einbau in Profile
Low cost and high stability
Parameter
ohne Gehäuse
Part No. Iuput Voltage Current Output Remark 1
dimmbar mit Touchsensor
43LED/589 12-24VDC 1x3A 1x(36-72)W Constant Voltage
Eingangsspannung 12-24VDC, 1x 3A
Product Size
42 mm
von 36-72 Watt
L 42/B 10/H 10mm
Brief introduction of buttons Bestell­Nr.
V+
43LED/589
V-
Wiring diagram
N
Power Supply
110-230VAC input
12-24VDC
L
V+
12-24VDC input
W
69591/SET
2 Stk. Halteklammern
45°, inkl. Schrauben
Bestell­Nr.
69591/SET
Installation attention
(1) Put mini sensor dimmer switch into profiles when power is off.
(2) When install it in high humidity places (for example, bathroom / kitchen), please make sure
your LED profile is isolated against water. Otherwise it will affect the sensitivity of touch sensor.
(3) Pay attention to polarity. Reverse polarity will destroy the module.
(4) To prevent the cover from being scratched, it's better to use a white hard paper cover on the
above of spring. Then install it. Below is the picture for reference:
Safety & Warnings
1) The product shall be installed and serviced by a qualified person.
2) IP20.Please avoid the sun and rain. When installed outdoors, please ensure it is mounted in a water proof
Remark 2
enclosure.
3) Always be sure to mount this unit in an area with proper ventilation to avoid overheating.
Mini touch sensor
dimmer & switch, 4) Please check if the output voltage of any LED power supplies used comply with the working voltage of the
for aluminum profile
product.
5) Never connect any cables while power is on and always assure correct connections to avoid short circuits
before switching on.
6) Please ensure that the cable is secured tightly in the connector
7) For update information please consult your supplier.
Warranty Agreement
1) We provide lifelong technical assistance with this product:
3-year warranty. We print date on every products, for example :1125 means year 2011,week 25.The
warranty is for free repair or replacement and covers manufacturing faults only.
For faults beyond the 3-year warranty we reserve the right to charge for time and parts.
2) Limited Warrenty
LED+ Any defects caused by wrong operation.
Any damages caused by unauthorized removal, maintenance, modifying, incorrect connection and
LED-
replacement of chips.
Any damages due to transportation, vibration etc. after purchase.
Any damages caused by earthquake, fire, lightning, pollution and abnormal voltage.
Any damages caused by negligence, inappropriate storing at high temperatures and humidity or near
harmful chemicals.
Product has been updated
3) Repair or replacement as provided under this warranty is the exclusive remedy to the customer.
W
Short press on the blue/white led :on/of
Long press on the blue/white led:dim up
long press again dim down
PC cover:around 1.5mm