Troubleshooting - Geneva Touring S Bedienungsanleitung

When the TOURING S is powered for the first time, the display will show 'Wel-
come to GENEVA'.
OVERVIEW
You can play music from the following sources:
• FM radio.
• DAB radio.
• Mobile phone or computer via Bluetooth.
• Other devices with a line-in cable.
USING TOURING S
FM Radio
1.Press until the display shows "FM" and a frequency, for example
"103.2".
2.Select an FM station with and :
• Use a single touch: change frequency by 0.1MHz.
• Hold down for a short time: automatically search for the next or previous
station.
3.After a few seconds the display will show the RDS information.
DAB / DAB+
1.Press until the display shows "DAB/DAB+".
2.Select a DAB station with and . TOURING S is compatible with
6
DAB, DAB+, DMR and DMB. When using your TOURING S for the first time, the
radio needs to find available radio stations in your region (a scan function). After
a SCAN, the stations will be automatically stored.
• Hold down the button until "SCAN" displays. The indication will blink for a
few seconds, then the display will confirm that the first station has been found.
"SCAN" is also needed after traveling to a new location that provides different
radio stations, or when you move the radio to a different room with a different
radio reception.
Presets
You can save six FM stations plus six DAB stations. To save a preset:
1. Select the station you want to save.
2. Long press until the display shows "PRESET 1" as blinking.
3. If you want to save using a different PRESET number, press
select the desired number.
4. After, long press to save the station.
To recall a preset:
1. Short press . The display will show the first saved preset. If a saved
station is playing , the display will show the next saved preset.
2. If you want to recall a different station, press again.
3. Wait two seconds and the unit will play the selected preset station.
Line-in
To connect a source device to your TOURING S, you need a stereo audio cable
with 3.5mm jack plug connector.
1. Connect the cable to the audio source device (headphone or line-out plug).
2. Connect the other end of the cable to the line-In socket on the back of the
TOURING S. The unit will automatically change mode to LINE IN.
3. By disconnecting the cable from TOURING S, the unit will return to the previ-
ously selected mode.
Bluetooth
Mobile phones and computers with Bluetooth can connect to the TOURING S
and play music. The mobile phone or computer must support Bluetooth A2DP.
Initial set-up ("pairing"):
1. Press the key. The display will show "BLUE". Wait for 20 seconds until
again and
the display shows "PAIRING" as blinking .
2. Select "settings" on your mobile phone. Select "General/Bluetooth". Turn on
Bluetooth. New Bluetooth devices are discovered automatically (on some devic-
es you will need to press 'scan').
3. After a few seconds, "TOURING S" will appear.
4. Select "TOURING S". The mobile phone is now connecting ("pairing") to the
TOURING S.
5. If the mobile phone asks for a PIN, enter "0000" (four zeros).
6. You can now play music on your mobile phone and listen to it on the TOUR-
ING S.
Playing music
Most mobile phones will connect automatically to the TOURING S after initial
set-up ("pairing").
1. Be sure the Bluetooth setting on your mobile phone is ON.
2. Press the key. The display will show "BLUE", then will show
"SEARCH", as blinking.
3. After a few seconds, TOURING S will automatically connect to your mobile
phone. The display will show "CONNECT".
4. Play music on the mobile phone and the music will start playing on the TOUR-
ING S automatically after a few seconds.

TROUBLESHOOTING

Why is my mobile phone not connecting?
You will find more detailed information on various mobile phones on our support
pages at www.genevalab.com.
The TOURING S will not turn on, and the display shows "LOW BATT".
The battery is slow on charge.
Connect the power adapter to the TOURING S and the battery will begin charg-
ing. You can use the TOURING S while the charger is connected.
The TOURING S will not turn on, and nothing happens.
If the battery is very low, there will not be enough power to even turn on the
display. TOURING S can be turned on after it has been connected for a short
while to the power adapter.
Why is the TOURING S turning off after a while?
After a few minutes of inactivity, the device will automatically turn itself off to save
battery.
What is the pin for a Bluetooth connection?
The PIN is 0000 (four zeros). Not all computers or mobile phones require a pin
7