Herunterladen Inhalt Inhalt Diese Seite drucken

Care And Maintenance - Velleman CS100N Bedienungsanleitung

Basismodell
Vorschau ausblenden Andere Handbücher für CS100N:
Inhaltsverzeichnis

Werbung

Verfügbare Sprachen
  • DE

Verfügbare Sprachen

  • DEUTSCH, seite 27
 The angle at which the object rests in the ground.
 The depth of the object.
 The amount of iron in the object.
 The size of the object.
h. Pinpointing a target
Accurately pinpointing a target makes digging it up easier.
Accurate pinpointing takes practice, and we suggest you practice finding and digging up small
metal objects on your own property before you search other locations.
Sometimes, targets are difficult to accurately locate due to the sweep direction. Try changing
your sweep direction to pinpoint a target.
Follow these steps to pinpoint a target.
1. When the detector detects a buried target, continue sweeping the search coil over the target in
a narrowing side-to-side motion.
2. Make a visual note of the exact spot on the ground where the detector beeps.
3. Stop the search coil directly over this spot on the ground. Then move the search coil straight
forward away from you and straight back toward you a couple of times.
Make a visual note of the exact spot on the ground where the detector beeps.
4. Repeat Steps 1-3 at a right-angle to the original search line, making an "X" pattern. The target
will be directly below the "X" at the point of the loudest response [Q].
Notes:
 If trash in an area is so heavy that you get false signals, slow your sweep and use shorter
sweeps.
 Recently buried coins might not respond the same as coins buried for a long period of time
because of oxidation.
 Some nails, nuts, bolts, and other iron objects (such as old bottle caps) oxidise and create a
"halo" effect. A halo effect is caused by a mixture of natural elements in the ground and the
oxidation created by different metals. Because of the metal mixtures, target signals might not be
in a "fixed" position. This effect makes these objects very hard to detect accurately. (See "Fine-
Tuning the Detector").

7. Care and maintenance

Wipe the detector with a damp cloth occasionally to keep it looking new. Do not use harsh
chemicals, cleaning solvents or strong detergents to clean the detector.
 Modifying or tampering with the detector's internal parts can cause a malfunction and might
invalidate its warranty.
 The search coil supplied with the detector is waterproof and can be submerged in either fresh or
salt water. However, do not let water enter the detector's control housing. After using the search
coil in salt water, rinse it with fresh water to prevent corrosion of the metal parts.
8. Troubleshooting
If your detector is not working as it should, follow these suggestions to see if you can eliminate the
problem.
PROBLEM
The detector displays or
sounds false signals
The display does not show the
correct metal type when the
detector finds a target or the
detector sounds more than
one type of tone when it finds
a target.
V. 04 – 07/03/2018
CS100N
You might be sweeping the detector's search coil too fast or at the
wrong angle. Sweep the search coil more slowly and hold the
detector correctly. See "Testing and Using the Detector" and
"Pinpointing a Target".
The detector might sound a false signal if it detects heavily oxidised
metals. Try pinpointing the target from several different angles (see
"Pinpointing a Target"). If the detector does not display and sound
the same signal each time, the target is probably heavily oxidised
metal.
There might be more than one target in the area you are searching.
The target might be a type of metal that the detector does not
recognise.
If the target is heavily oxidised, the detector might not display the
correct metal type. This is not a malfunction.
7
SUGGESTION
©Velleman nv

Quicklinks ausblenden:

Werbung

Inhaltsverzeichnis
loading

Inhaltsverzeichnis