HQ Power VDP1500ASM Bedienungsanleitung Seite 3

• Familiarise e yourself w
operation by unqualif
unprofessi ional use of
• Use the or riginal pack
• All modific cations of th
• Only use t the device f
electrosho ocks, crash,
4. . Mountin ng the d
• Have the d device insta
norms.
• The carryi ng construc
without de eforming.
• The install lation must
• Never stan nd directly
qualified te echnician c
• Install the device in a
• Overhead mounting r
installation n material t
attempt to o install the
result in in njuries.
• Adjust the e desired in
• Make sure e there is no
• Have a qu alified elec
• Connect th he device to
• The install lation has t
5. . Use
a. descriptio on
1. DIP sw witches
2. DMX i nput
3. DMX o output
4. wirele ess controlle
5. input for wired c
6. outpu t from wire
7. power r supply inp
fuse h holder
8. on/off f switch
b. Adjusting g the Outp
• Unscre ew and rem
• Set to o the desire
• Fix the e angle by
machi ne.
c. LEDs
• Red LE ED: Device
• Green LED: Devi
d. Turbo Fun nction
This func ction can be
output in n e.g. cold r
environm ment) or wh
e. DMX
• DMX51 12 Connec
Connec ct the provid
other si ide to the m
linked t through ser
input an nd output c
• DMX51 12 Chain w
A DMX terminator
has to r run a long d
discos). . The termi
by elect trical noise
120Ω re esistor betw
01/ /09/2010
VDP
with the fun nctions of t
fied people . Any dama
f the device e.
kaging if the e device is
he device a are forbidde
for its inten nded purpo
, etc. Using g the device
evice
alled by a q qualified pe
ction must be able to
t always be e secured w
below the d device whe
check the d evice once
a location w with few pa
requires ex xtensive ex
to be used... ... Have the
e device you urself if you
clination an ngle via the
o flammabl e material
trician carr ry out the e
o the mains s with the p
to be appro oved by an
er (not incl .)
ontroller (i ncl.)
ed controlle er
put connect tor and
put Angle
move both k knobs.
ed angle.
screwing b both knobs
e is heating .
ce is ready y for use.
e useful wh hen you nee
rooms (smo oke liquid w
hen the smo oke liquid i
ction
ded XLR ca able to the f
male 3-pin XLR input o
rial linking. The linking
connectors. .
with Termi ination
is recomm mended for
distance or r is in an ele
nator preve ents corrup
. The DMX terminator
ween pins 2 2 and 3, wh
P1500ASM M
he device b before actu
age that m ay occur w
to be trans sported.
en for safet ty reasons.
se. All othe er uses may
e in an una uthorised w
erson, respe ecting EN 6
support 10 0 times the
with a secon ndary attac
en it is bein g mounted
a year and d once befo
assers-by th hat is inacc
perience: c calculating w
e material a and the dev
u lack thes e qualificat
e mounting bracket an
within a 0. 5m radius
electric con nection.
power plug . Do not co
expert befo ore the dev
back into t he smoke
ed a more i intense sm
will be affec cted by a c
s diluted.
female 3-p in XLR outp
of the VDP P1500ASM
g cable sho ould be a tw
installation s where th
ectrically n oisy enviro
ption of the e digital con
r is simply a an XLR plug
hich is then n plugged in
3
ally using i t. Do not a
ill most pro obably be d
y lead to sh hort circuits
way will voi id the warra
60598-2-17 7 and all oth
weight of t the device
hment e.g. a safety c
, removed or serviced
ore you brin ng it into se
essible to u unauthorise
workload li mits, deter
vice itself ch hecked reg
tions as imp proper insta
nd tighten t the bracket
of the devi ice.
onnect it to a dimming
vice is taken n into servi
oke
old
put of your r controller
. Multiple V VDP1500A
wo-core scr reened cabl
e DMX cab le
onment (e.g g.
ntrol signal
g with a
nto the XLR R
Rev. 0 01
allow
due to
s, burns,
anty.
her applica ble
for 1 hour
able.
d. Have a
ervice.
ed persons. .
rmining the e
ularly. Do n not
allation ma ay
t screws.
g pack.
ice.
and the
ASMs can b be
e with XLR R
n nv
©Velleman