Technical Data; Noise/Vibration Information; Changing The Tool - Bosch PHO 3100 Originalbetriebsanleitung

(5) On/off switch
(6) Changeover lever for chip ejector direction
(7) Planer base plate
(8) V-grooves
(9) Handle (insulated gripping surface)
(10) Blade head
(11) Clamping element for planer blade
(12) Fastening screw for planer blade
(13) HM/TC planer blade
(14) Hex key
(15) Extraction hose (dia. 35 mm)
A)
(16) Chip/dust bag
(17) Parallel guide
(18) Scale for rebate width
(19) Locking nut for rebate width setting
(20) Fastening screw for parallel/angle guide
A)
(21) Angle stop
(22) Locking nut for angle setting
(23) Fastening screw for rebate depth guide
A)
(24) Rebate depth guide
(25) Parking rest
A) Accessories shown or described are not included with the
product as standard. You can find the complete selection of
accessories in our accessories range.

Technical data

Planer
Article number
Rated power input
Power output
No-load speed
Cutting depth
Rebate depth
Max. planing width
Weight according to EPTA Proced-
ure 01:2014
Protection class
The specifications apply to a rated voltage [U] of 230 V. These spe-
cifications may vary at different voltages and in country-specific mod-
els.

Noise/vibration information

Noise emission values determined according to EN
62841-2-14.
Typically the A-weighted noise level of the power tool is:
Sound pressure level 82 dB(A); Sound power level 93
dB(A). Uncertainty K=3 dB.
Wear hearing protection
Vibration total values a (triax vector sum) and uncertainty K
h
determined according to EN 62841:
Bosch Power Tools
a =4,5 m/s
h
The vibration level and noise emission value given in these
instructions have been measured in accordance with a
standardised measuring procedure detailed in EN 62841
and may be used to compare power tools. They may also be
used for a preliminary estimation of vibration and noise
emissions.
The given vibration level and noise emission value represent
the main applications of the power tool. However, if the
power tool is used for other applications, with different ap-
plication tools or is poorly maintained, the vibration level
and noise emission value may differ. This may significantly
increase the vibration and noise emissions over the total
A)
working period.
To estimate vibration and noise emissions accurately, the
times when the tool is switched off or when it is running but
not actually being used should also be taken into account.
This may significantly reduce vibration and noise emissions
over the total working period.
Implement additional safety measures to protect the oper-
ator from the effects of vibration, such as servicing the
power tool and application tools, keeping the hands warm,
A)
and organising workflows correctly.
A)
Fitting
u

Changing the tool

u
PHO 3100
3 603 B71 ...
Use only original Bosch HM/TC planer blades. The hard
W 750
metal (HM/TC) planer blade has two cutting edges and can
W 420
be turned. If both cutting edges become blunt, the planer
rpm 16,500
blade (13) needs to be changed. The HM/TC planer blade
must not be resharpened.
mm 0–3.1
Removing the planer blade (see figure A)
mm 0–9
To turn or replace the planer blade (13), turn the blade head
mm 82
(10) until it is parallel to the planer base plate (7).
kg 2.6
➊ Loosen the two fastening screws (12) using the hex key
(14) (approx. 1–2 turns).
/ II
➋ If necessary, loosen the clamping element (11) by lightly
striking it with an appropriate implement, e.g. a wooden
wedge.
➌ Use a piece of wood to push the planer blade (13) to the
side and out of the blade head (10).
Fitting the planer blade (see figure B)
The guide groove on the planer blade ensures a constant,
even height setting when changing or turning the blade.
If necessary, clean the knife seat in the clamping element
(11) and the planer blade (13). When fitting the planer
blade, ensure that it is securely seated in the mounting guide
of the clamping element (11) and is aligned flush with the
2 2
, K=1,5 m/s .
Pull the plug out of the socket before carrying out any
work on the power tool.
Take care when changing the planer blade. Do not pick
up the planer blade by the cutting edges. You may be
injured by the sharp cutting edges.
1 609 92A 4AM | (08.08.2018)
English | 13