General Information - Atlas Copco RRH 06P Bedienungsanleitung

WMV-Dresden, Ersatzteilservice für Elektrowerkzeuge, Motor- und Gartengeräte
RRH 06P
• The punch retainer spring is designed for use on
RRH 04/06/08 only.
• Turn the exhaust guard to the desired position.
For safer use – please note
• Check regularly that the retainer is fully screwed
on to the cylinder.
• If different RRH 04/06/08P models are in use at
the same workplace all 1.7 mm wire retainers
(black) shall be withdrawn and replaced by 2.0
mm wire retainers (yellow) on all hammers. This
is due of safety reasons, i.e. to prevent mixing up
the retainers and using the wrong type on the
wrong hammer model.
A
This machine does not satisfy the normal re-
quirements for use in explosive environment
as the machine casing contains aluminium.

General information

EC DECLARATION OF CONFORMITY
We, Atlas Copco Tools AB, S-105 23 STOCK-
HOLM SWEDEN declare under our sole responsib-
ility that our product (with type and serial number,
see front page) and in combination with our accessor-
ies, to which this declaration relates is in conformity
with the appropriate standard(s):
EN 792-4
and in accordance with the following directive(s):
98/37/EEC
Stockholm, October 2006
Lennart Remnebäck, General Manager
Signature of issuer
Installation
Air quality
• For optimum performance and maximum machine
life we recommend use of compressed air with a
dew point between +2°C and +10°C. Installation
of an Atlas Copco refrigeration-type air dryer is
recommended.
• Use a separate air filter of type Atlas Copco FIL,
removes solid particles larger than 15 microns and
more than 90 % of liquid water, installed as close
as possible to the machine and prior to any other
air preparation unit like REG or DIM (please see
Air Line Accessories in our main catalogue). Blow
out the hose before connecting.
Models which need air lubrication:
• The compressed air must contain a small quantity
of oil. We strongly recommend that you install an
Atlas Copco oil-fog lubricator DIM, to be set
normally at 3-4 drops/min (50mm
cycle running tools, or an Atlas Copco single-point
lubricator type Dosol for short cycle running tools.
For Dosol setting please see Air Line Accessories
in our main catalogue.
Lubrication-free models:
• Regarding lubrication free tools it is, at the cus-
tomers option, no disadvantage if the compressed
air contains a small quantity of oil as supplied
from a lubricator DIM or Dosol.
An exception is turbine tools that should be kept
oil free.
Compressed air connection
• The machine is designed for a working pressure
(e) of 6–7 bar = 600–700 kPa = 87–102 psi.
• Blow out the hose before connecting.
Installation proposal
Choosing the correct couplings, hose and clamps can
be a troublesome digging into details. To save your
time and to ensure correct capacity of the airline in-
stallation, from the tapping point to the tool, we offer
you an installation proposal.
ErgoNIP 10
For more information please read, Atlas Copco In-
dustrial Power Tools catalogue Ordering No. 9837
3000 01.
Atlas Copco Tools - 9836 1974 00
Safety and operating instructions
Filtered, regulated and oil fog lubricated air for a
max. air flow of 10 l/s
BALL VALVE + MIDI F/RD 15 + ERGOQIC 10
8202 0829 11
5 m PVC 10
5 m RUBAIR 10
8202 1180 18 / 8202 1180 43
ErgoNIP 10 0.7 m CABLAIR 10
0.7 m RUBAIR 10
8202 1180 19 / 8202 1180 42
3 3
/m ) for long
ErgoQIC 10
ErgoNIP 10 M08
Nipple
Male 1/4" BSPT
5