Installation - Hallde RG-400 Bedienungsanleitung

USER INSTRUCTIONS
HALLDE
RG - 400
CAUTION!
Take great care not to injure your hands on
the sharp blades of the cutting tools and
feed cylinder and on moving parts.
The machine may be installed only by a
qualified service mechanic.
Never put your hands in any of the feed
attachments or the feed cylinders other
than for cleaning.
Always use the pestles for cutting by means
of the 4-tube insert.
Never put your hands in the machine outlet
when the feed cylinder is lowered and the
locking handle is raised.
The agitator device, locking bolt and deco-
ring device must be tightened (by tur ning
them anti-clockwise) and unscrewed (clock-
wise), by means of the wrench.
Always press the machine stop button
before fitting or removing cutting tools, etc.
even if the machine is not running.
Before cleaning, switch off the machine and
remove the plug from the wall socket or turn
off the mains switch.
When using the 4-tube insert never use
cutting tools larger than 10 mm.
Only a qualified service mechanic may
repair the machine and open the machine
housing.
Do not use the machine to cut frozen foods.
Remove all hard parts from foods before
cutting (e.g., apple stems, woody parts of
turnips, etc.) to avoid damaging the cutting
blades.
This appliance is not to be operated by
children or persons with reduced physical,
sensory or mental capabilities or persons
lacking experience of such appliances,
unless they are given adequate instruction
or supervision.
UNPACKING
Check that all parts have been delivered, that
4
the machine operates as intended, and that
nothing has been damaged in transit.
The machine supplier should be notified of any
shortcomings within eight days.

INSTALLATION

Connect the machine to an electric power
supply that is suitable for the machine.
Remove the cutting tool before installing the
machine.
Reset the adjustable feet as necessary to make
sure that the machine stands firmly.
Locate the hanger for the cutting tools on the
wall in the vicinity of the machine for convenient
and safe use.
Check that the shaft rotates clockwise.
Check that the machine stops when the locking
handle is folded down.
Check that the machine stops when the locking
knob for the feed hopper attachment or 4-tube
insert is turned clockwise to the unlocked posi-
tion, and that the machine restarts when the
locking knob is turned anti-clockwise to the
locked position.
Check that the machine stops when the manual
or pneumatic push feed attachment feed plate
is swung to the side so that the feed cylinder
opening is larger than 60 mm, and that the
machine restarts when it is swung back over
the feed cylinder.
If the machine does not function correctly, it
must receive attention before it is taken into
operation.
ALWAYS CHECK BEFORE USE
Remove the plug from the power supply socket
or open the isolating switch, and then check
that the electric cable is in good condition and
is not cracked on the outside.
WITH THE MANUAL/PNEUMATIC
FEEDER:
Check that, with a cutting tool fitted, the
machine stops within 2 seconds as soon as the
pusher plate is swung out to the side more than
60 mm, and re-starts when the pusher plate is
swung back over the feeder.
Check that the machine cannot be started with
the feed cylinder removed and with the pusher
plate lowered.
If either of the two safety functions does not
perform as intended or if the electric cable is
cracked, call in a qualified service mechanic or
electrician to remedy the fault before connec-
ting the machine back to the power supply.
Check that the pusher plate shaft runs freely.
If the shaft does not run freely, clean it carefully
and lubricate it with a few drops of machine oil.
Check that the cutting tools are in good condi-
tion and are sharp.
With regard to cutting tools, see page 61.
WITH THE FEED HOPPER:
Remove the plug from the power supply socket
or open the isolating switch, and then check
that the electric cable is in good condition and
is not cracked on the outside.
Check that the machine cannot be started
when the feed cylinder for the feed hopper is
fitted but the feed hopper itself is not.
If the safety function does not perform as
intended or if the electric cable is cracked, call
in a qualified service mechanic or electrician
to remedy the fault before connecting the
machine back to the power supply.
Check that the cutting tools are in good condi-
tion and are sharp.
With regard to cutting tools, see page 61.
WITH THE 4-TUBE INSERT:
Remove the plug from the power supply socket
or open the isolating switch, and then check
that the electric cable is in good condition and
is not cracked on the outside.
Check that the machine cannot be started
when the feed cylinder for the 4-tube insert is
fitted but the4-tube itself is not.
If the safety function does not perform as
intended or if the electric cable is cracked, call
in a qualified service mechanic or electrician
to remedy the fault before connecting the
machine back to the power supply.
Check that the cutting tools are in good condi-
tion and are sharp.
With regard to cutting tools, see page 61.
TYPE OF PROCESSING
Slices, dices, grates, shreds, cuts julienne,
crimping slices and potato chips in a variety
of dimensions, depending on the cutting tool
selected. Processes vegetables, fruit, dry
bread, cheese, nuts, mushrooms etc.
USERS
Restaurants, shop kitchens, hospitals, schools,
fast food outlets, catering, pizzerias, ships,
central kitchens, institution kitchens, food
processing industries etc.
CAPACITY
Up to 3 000 portions per day, 15 kg per minute
with the manual feeder and 40 kg per minute
with the feed hopper.
USING THE FEEDERS
MANUAL FEEDER, ERGO LOOP/
PNEUMATIC PUSH FEEDER:
The large feed compartment is used mainly
for bulk feeding of all sorts of products and
for cutting larger products such as cabbage.
The large feed compartment is also used when
the product is to be cut in a specific direction,
such as tomatoes and lemons. Place/stack the
products as shown in the picture.
HALLDE • User Instructions