Laser Information - Sharp AR-6020 Erste Schritte

Laser information

Wave length 785 nm + 10 nm / -15 nm
Pulse times (8.50 µs ± 29.6 ns) / 7 mm
Output power Max 0.4 mW
Caution
Use of controls or adjustments or performance of procedures other than those
specified herein may result in hazardous radiation exposure.
This Digital Equipment is CLASS 1 LASER PRODUCT (IEC 60825-1 Edition 2-2007).
Caution
For a complete electrical disconnection, pull out the main plug.
The socket-outlet shall be installed near the equipment and shall be easily
accessible.
Shielded interface cables must be used with this equipment to
maintain compliance with EMC regulations.
The equipment should be installed near an accessible socket outlet
for easy disconnection.
Each instruction also covers the optional units used with these products.
WARNING:
This is a Class A product. In a domestic environment this product
may cause radio interference in which case the user may be
required to take adequate measures.
Software licence
The SOFTWARE LICENCE will appear when you install the software
from the CD-ROM. By using all or any portion of the software on the
CD-ROM or in the machine, you are agreeing to be bound by the
terms of the SOFTWARE LICENCE.
• The explanations in this manual assume that you have a working knowledge
of your Windows or Macintosh computer.
• For information on your operating system, please refer to your operating
system manual or the online Help function.
• The explanations of screens and procedures in this manual are primarily for
Windows 7 in Windows environments. The screens may vary depending on
®
the version of the operating system.
• This manual contains explanations of the PPD driver. However, please note that
the PPD driver are not available and do not appear on the software for installation
in some countries and regions.
In this case, please install the English version if you want to use these drivers.
• Considerable care has been taken in preparing this manual. If you have any
comments or concerns about the manual, please contact your dealer or
nearest authorised service representative.
• This product has undergone strict quality control and inspection
procedures. In the unlikely event that a defect or other problem is
discovered, please contact your dealer or nearest authorised service
representative.
• Aside from instances provided for by law, SHARP is not responsible for failures
occurring during the use of the product or its options, or failures due to incorrect
operation of the product and its options, or other failures, or for any damage that
occurs due to use of the product.
This product is designed for commercial application only and as such it falls
outside the scope of Regulation (EC) 1275/2008 implementing EU Directive
2005/32/EC on eco-design requirements for standby and off mode electric
power consumption. Sharp does not recommend the product for domestic
application and will not accept any liability for such use.
Warranty
While every effort has been made to make this document as accurate and
helpful as possible, SHARP Corporation makes no warranty of any kind with
regard to its content. All information included herein is subject to change
without notice. SHARP is not responsible for any loss or damages, direct or
indirect, arising from or related to the use of this operation manual.
© Copyright SHARP Corporation 2014. All rights reserved. Reproduction,
adaptation or translation without prior written permission is prohibited, except
as allowed under copyright laws.
Notice for users in the UK
MAINS PLUG WIRING INSTRUCTIONS
The mains lead of this equipment is already fitted with a mains plug which is
either a non-rewireable (moulded) or a rewireable type. Should the fuse need to
be replaced, a BSI or ASTA approved fuse to BS1362 marked
and of the same rating as the one removed from the plug must be used.
Always refit the fuse cover after replacing the fuse on the moulded plug. Never
use the plug without the fuse cover fitted.
In the unlikely event of the socket outlet in your home not being compatible with
the plug supplied either cut-off the moulded plug (if this type is fitted) or remove
by undoing the screws if a rewireable plug is fitted and fit an appropriate type
observing the wiring code below.
DANGER: The fuse should be removed from the cut-off plug and the plug
destroyed immediately and disposed of in a safe manner. Under no circumstances
should the cut-off plug be inserted elsewhere into a 13A socket outlet as a serious
electric shock may occur.
To fit an appropriate plug to the mains lead, follow the instructions below:
IMPORTANT: The wires in this mains lead are coloured in accordance with the
following code:
GREEN-AND-YELLOW:
BLUE:
BROWN:
As the colours of the wires in this mains lead may not correspond with coloured
markings identifying the terminals in your plug, proceed as follows:
The wire which is coloured GREEN-AND-YELLOW must be connected to the
terminal in the plug which is marked with the letter E, or by the safety earth
symbol , or coloured green or greenand-yellow.
The wire which is coloured BLUE must be connected to the terminal which is
marked with the letter N or coloured black.
The wire which is coloured BROWN must be connected to the terminal which is
marked with the letter L or coloured red.
If you have any doubt, consult a qualified electrician.
WARNING: THIS APPARATUS MUST BE EARTHED.
Noise emission
Noise emission values
The following shows noise emission values as measured according
to ISO7779.
Sound power level L
Operating
(continuous printing)
Standby mode
(Low power level
mode)
Sound pressure level L
Operating
Bystander
(continuous
positions
printing)
Standby Bystander
mode positions
Supplies
Standard supplies for this product that can replaced by the user
include paper and toner cartridges.
Be sure to use only SHARP-specified products for the toner
cartridges and transparency film.
GENUINE SUPPLIES
Storage of supplies
Proper storage
1. Store the supplies in a location that is:
• clean and dry,
• at a stable temperature,
• not exposed to direct sunlight.
2. Store paper in the wrapper and lying flat.
3. Paper stored in packages standing up or out of the wrapper may curl or
become damp, resulting in paper misfeeds.
Storing toner cartridges
Store a new toner cartridge box horizontally with the top side up. Do not store
a toner cartridge standing on end. If stored standing on end, the toner may not
distribute well even after shaking the cartridge vigorously, and will remain inside
the cartridge without flowing out.
Supply of spare parts and consumables
The supply of spare parts for repair of the machine is guaranteed for at least 7 years
following the termination of production. Spare parts are those parts of the machine
or
which may break down within the scope of the ordinary use of the product, whereas
those parts which normally exceed the life of the product are not to be considered as
spare parts. Consumables too, are available for 7 years following the termination of
production.
Safety data sheet
The SDS (Safety Data Sheet) can be viewed at the following URL
address:
http://www.sharp-world.com/corporate/eco/env-info/sds/index.html
3
Earth
Neutral
Live
WA d
AR- AR- AR- AR- AR-
6020 6020D 6020N 6020NR 6023
6.82 6.83 6.80
6.89 B
B B
3.11 3.13 3.10
3.12 B
B B
pAm
AR- AR- AR- AR- AR-
6020 6020D 6020N 6020NR 6023
52.7 53.3 52.5
52.7 dB
dB dB
15.9 15.7 15.8
15.7 dB
dB dB
• Operating: with option AR-RP11 + MX-CS12 + AR-DS19.
For best copying results, be sure to use only
Sharp Genuine Supplies which are designed,
engineered, and tested to maximize the life
and performance of Sharp products. Look
for the Genuine Supplies label on the toner
package.
AR- AR- AR-
6023D 6023N 6023NR
6.86
6.82 B
B B
3.10
3.20 B
B B
AR- AR- AR-
6023D 6023N 6023NR
53.4
52.2 dB
dB dB
16.0
15.8 dB
dB dB