Technical Data; Noise/Vibration Information - Bosch PFS 105 E Originalbetriebsanleitung

OBJ_BUCH-420-002.book Page 16 Tuesday, August 23, 2011 12:08 PM
16 | English

Technical Data

Fine-spray System
Article number
Rated power input
Spraying capacity
Atomising output
Required time for application
2
of paint on 5 m
Container capacity for spray
material
Length of air hose
Weight according to
EPTA-Procedure 01/2003
Protection class
The values given are valid for a nominal voltage [U] of 230 V. For differ-
ent voltages and models for specific countries, these values can vary.
Please observe the article number on the type plate of your machine.
The trade names of the individual machines may vary.

Noise/Vibration Information

Measured sound values determined according to EN 60745.
Typically the A-weighted sound pressure level of the product
is 74 dB(A). Uncertainty K=3 dB.
The noise level when working can exceed 80 dB(A).
Wear hearing protection!
Vibration total values a (triax vector sum) and uncertainty K
h
determined according to EN 60745:
2 2
a < 2.5 m/s , K= 1.5 m/s .
h
The vibration emission level given in this information sheet
has been measured in accordance with a standardised test
given in EN 60745 and may be used to compare one tool with
another. It may be used for a preliminary assessment of expo-
sure.
The declared vibration emission level represents the main ap-
plications of the tool. However if the tool is used for different
applications, with different accessories or poorly maintained,
the vibration emission may differ. This may significantly in-
crease the exposure level over the total working period.
An estimation of the level of exposure to vibration should also
take into account the times when the tool is switched off or
when it is running but not actually doing the job. This may sig-
nificantly reduce the exposure level over the total working pe-
riod.
Identify additional safety measures to protect the operator
from the effects of vibration such as: maintain the tool and the
accessories, keep hands warm, organise work patterns.
Declaration of Conformity
We declare under our sole responsibility that the product de-
scribed under "Technical data" is in conformity with the fol-
lowing standards or standardization documents: EN 60335
and the directives 2011/65/EU, 2006/42/EC,
2004/108/EC including their amendments.
Technical file (2006/42/EC) at:
Robert Bosch GmbH, Dept. PT/ESC,
D-70745 Leinfelden-Echterdingen
1 609 929 Y14 | (23.8.11)
Dr. Egbert Schneider
Senior Vice President
PFS 105 E
Engineering
3 603 B06 2..
W 350
g/min 150
W 0–105
Robert Bosch GmbH, Power Tools Division
D-70745 Leinfelden-Echterdingen
Leinfelden, 22.08.2011
min 6
Assembly
ml 800
Before any work on the machine itself, pull the mains
m 3.4
plug.
kg 4.9
Connecting the Air hose (see figures A1
/II
– Take the air hose 13 out of the accessory compartment
20.
– Remove the protective caps from both ends of the air hose.
Connecting to the spray gun:
– Firmly insert an SDS connector 14 of the air hose in align-
ment with the arrow mark into the hose port of the spray
gun 6.
– Turn the SDS connector until the lock can be heard to
latch.
Connecting the base unit:
– Firmly insert the second SDS connector of the air hose in
alignment with the arrow mark into the port of the base unit
18.
– Turn the SDS connector until the lock can be heard to
latch.
Note: After use, reattach the protective hose caps to the hose
ends.
Operation
Preparing for Operation
Spraying on the sides of water bodies (lakes, rivers,
etc.) or neighbouring surfaces in the direct catchment
area is not permitted.
When purchasing paint, varnish and spray material, pay at-
tention to their environmental compatibility.
Preparing the Spray Surface
Note: Cover off the vicinity of the spray surface thoroughly
and generously.
The spray mist contaminates the environment. When spray-
ing in enclosures, surfaces not covered can become contami-
nated.
The spray surface must be clean, dry and grease-free.
– Roughen smooth surfaces and then remove the sanding
dust.
Dr. Eckerhard Strötgen
Head of Product
Certification
A2)
–
Bosch Power Tools