Setup Menu - JBSystems usb 2.2 Mk2 Bedienungsanleitung

ENGLISH

SETUP MENU

To increase flexibility some parameters of the USB2.2 MK2 MK2 can be changed in the setup menu.
 To enter the SETUP menu, press the TIME button (19) of the left player for about 3seconds.
 Use the TRACK knob (9) to browse the different menu options of the main menu.
 Press the TRACK knob (9) to select the menu option you want to change:
 Use the TRACK knob (9) to change the parameters of the selected menu option.
 If the menu option has submenus, use the JOG-WHEEL (1) to browse these.
 Press the TRACK knob (9) again to return to the main menu.
 To save your settings: choose menu option 6 (EXIT & SAVE) and press the TRACK knob (9) 
1. SENSITIVITY: you can change the sensitivity of the tactile jog wheel to optimize the jog wheel
performance.
 Turn the TRACK knob (9) to select one of the 41 possibilities:
o ADJ. = 0:
o ADJ. = -20:
o ADJ. = +20: highest sensitivity
Press the TRACK knob (9) to save the new value and return to the main menu.
2. SLEEP TIME: to extend the lifetime of the laser, the unit goes automatically to sleep mode while not used
for 15 minutes (default). In this menu option you can change, the time it takes to enter sleep mode:
 Turn the TRACK knob (9) to select the desired time: "No SLEEP"  120 minutes.
Press the TRACK knob (9) to save the new value and return to the main menu.
3. Line Setup: you can configure how the text line shows information that is longer than 10 characters. You
can choose 3 different modes + some extra fine-tuning:
 There are 3 submenus: turn the JOG-WHEEL (1) to select a submenu.
o Submenu 1 - L1 Mode:
 Turn the TRACK knob (9) to select the desired setting:
o Submenu 2 – start/stop waiting time for scrolling:
 Turn the TRACK knob (9) to select the desired value:
o Submenu 3 – scrolling speed:
 Turn the TRACK knob (9) to select the desired value:
Press the TRACK knob (9) to save the new values and return to the main menu.
4. Firmware version / upgrading: use this option to check and/or upgrade the firmware versions.
 Turn the TRACK knob (9) to select the 3 firmware parts:
o CON: xx: shows the version of the control firmware
o DSP: xx: shows the version of the DSP firmware
o SER: xx: shows the version of the servo firmware
o Upgrade: blinks when the unit is ready to check if there are new firmware versions
available. See "FIRMWARE UPGRADING" for more information.
Press the TRACK knob (9) to return to the main menu.
5. Load defaults: If you really messed up things, you can still reload the default setting!
 While "Load Defaults" is shown on the display: press the TRACK knob (9) to load the defaults.
6. Exit & Save: if you want your changes to the setup menu to be permanently saved (also after switching
the unit off) you MUST use this option!
 Press the TRACK knob (9) : the display shows "Saving" and exits the setup menu.
FIRMWARE UPGRADING
We strongly suggest to regularly check the USB2.2 MK2 MK2 product page on www.jbsystems.be to see if
new firmware updates are available. Upgrading firmware should always be done very carefully!
 Download the file containing the upgrade file(s)
 Read the instructions and follow them strictly, otherwise you could damage your equipment...
JB SYSTEMS
®
neutral setting (default setting, OK in most cases)
lowest sensitivity
 L1 Mode = 1: text line scrolls and waits for a certain time before scrolling
starts again. You can set the waiting time in submenu2.
 L1 Mode = 2: text line scrolls only one time, then stops.
 L1 Mode = 3: text line scrolls continuously.
 Dis. = 0.5s  12.0s: waiting time in seconds.
 Run = 50  2000ms: 50ms = fast speed / 2000ms = slow speed
8/82
OPERATION MANUAL
USB2.2 MK2