Operation; Maintenance; Specifications - IMG STAGE LINE DJP-300USB Bedienungsanleitung

2) For transferring music pieces from a record to
a computer, connect the USB port USB TO
PC (3) via the USB cable provided to a USB
port of the computer.
An audio recording software will also be
required. If there is no corresponding soft-
ware on your computer, various programs
are available as freeware on the Internet for
download.
3) Finally connect the mains cable provided to
the mains jack AC IN (2), then connect the
mains plug to a mains socket (100 – 240 V~ /
50 – 60 Hz).

6 Operation

6.1 Playing a record
1) Remove the protective cap from the stylus
towards the front.
2) Switch on the turntable with the POWER
switch (1). The LED of the button MOTOR
OFF (7), the target light (20) and the LED of
the button "33" (21) will light up.
3) To select the speed, press the corresponding
button (21):
for 33 1 ⁄ rpm, press the left button "33"
3
for 45 rpm, press the right button "45"
for 78 rpm, press both buttons "33" and "45"
To indicate the speed selected, the corre-
sponding LED above the button will light up.
4) Put on the record. For single records, use the
adapter (12). It is easy to remove the adapter
from its recess: simply press its rear edge.
5) Open the lock (11) for the tone arm (13) to the
right. To lift the tone arm, set the tone arm lift
to the rear position.
6) Seize the tone arm on its handle (22) and
position the stylus above the beginning or the
desired spot on the record. Set the lever (10)
for the tone arm lift to the front position. The
tone arm will slowly be lowered onto the
record.
7) Press one of the Start / Stop buttons
The turntable platter will start rotating. To
stop and restart the record at any time while
playing, use one of the buttons
8) To stop playing, lift the tone arm with the lever
of the tone arm lift (10) and return it to the
tone arm support with your hand. Stop the
turntable platter with one of the buttons
9) After using the turntable, secure the tone arm
with the lock (11) and switch off the turntable
with the POWER switch (1).
6.2 Changing the speed
If required, it will be possible to increase or
decrease the speed of the turntable and thus the
pitch of a music piece with the control PITCH
ADJ. (14) by up to 10 %. In mid-position (control
will engage), the normal speed is adjusted, i. e.
1
precisely 33 ⁄ rpm, 45 rpm or 78 rpm.
3
6.3 Slowly starting or stopping
a record
To slowly start or stop a record:
1) Position the stylus above the desired spot of
the record without lowering it with the lever
(10) for the tone arm lift.
2) Press one of the buttons
rotation of the turntable.
3) Switch off the motor of the turntable platter
with the button MOTOR OFF (7). The LED of
the button will be extinguished.
4) Lower the stylus onto the record with the
lever (10) for the tone arm lift.
5) Slowly start the record with the button
MOTOR OFF.
6) To slowly stop the record, actuate the button
MOTOR OFF again at the desired spot.
6.4 Changing between forward
and reverse mode
As a special effect, the DJP-300USB will be
capable of changing the sense of rotation of the
turntable platter. For this purpose, shortly press
the button REVERSE (18). The red LED above
the button will light up if the reverse mode is acti-
vated.
Note: The turntable platter must be in rotation, other-
wise the button REVERSE will be without function.
7 Accessories
7.1 Replacement phono cartridge
system and replacement stylus
The phono cartridge system or the stylus is
easily replaced, if required. The corresponding
replacement parts are available from your
retailer, e. g. the magnetic phono cartridge sys-
tem EN-24 and the matching replacement stylus
EN-24SP from MONACOR.
1) To replace the stylus, tilt the white stylus sup-
port downwards and remove it. Put the new
stylus on the phono cartridge system.
2) To replace the phono cartridge system,
unscrew the cap nut (16) and remove the
(19).
headshell (17) from the tone arm (13).
3) Unscrew the phono cartridge system from the
.
support and remove the connecting wires.
4) Screw the new phono cartridge system onto
the support and connect the wires as follows:
blue left channel, positive pole
.
white left channel, negative pole
green right channel, positive pole
red right channel, negative pole
5) After replacing the phono cartridge system,
readjust the counterweight and the anti-skat-
ing value (
7.2 Replacement headshell
A replacement headshell (e. g. the headshell
EN-120 from MONACOR) including a phono
cartridge system will allow quick replacement,
if necessary. The headshell (16) is easily
All rights reserved by MONACOR
manual may be reproduced in any form or by any means for any commercial use.
(19) to start the
chapters 4.3 and 4.4).
® INTERNATIONAL GmbH & Co. KG. No part of this instruction
replaced by screwing it off and on. Then readjust
the counterweight and the anti-skating value
( chapters 4.3 and 4.4).
7.3 Felt slipmat
If the felt slipmat provided is lost or worn, a new
mat (DJP-2M) is available from "img Stage Line".

8 Maintenance

8.1 Cleaning
Clean the turntable housing with a soft cloth, dry
or slightly damp (not dripping wet). Do not use
any alcohol, chemicals or aggressive deter-
gents! To dust the stylus and the records, the
corresponding accessories will be available from
your retailer, e. g. the carbon fibre record clean-
ing brush DC-100 from MONACOR.
8.2 Transport
When dispatching the turntable, make sure that
the turntable and all other components of the unit
are wrapped in their original packaging or that
they are especially secured for transport. Any
damage due to incorrect transport of the
turntable (e. g. platter not removed from the axle,
not secured or the like) will not be covered by the
guarantee and any resulting repairs will be
charged!
When dispatching the turntable, always proceed
as follows:
1) Put the protective cap on the stylus.
2) Secure the tone arm (13) with the lock (11).
3) Unscrew the counterweight (8) for the tone
arm.
4) Remove the turntable platter from the axle,
wrap it separately and secure it against slip-
ping.
5) It is recommended to use the original packing
box.

9 Specifications

Turntable platter: . . . . . . . . ∅ 332 mm,
cast aluminium
Drive: . . . . . . . . . . . . . . . . belt drive
Speeds: . . . . . . . . . . . . . . . 33
Change of speed: . . . . . . . ±10 %
Starting torque: . . . . . . . . . 0.07 Nm
Starting time: . . . . . . . . . . . < 1 second
Wow and flutter: . . . . . . . . < 0.3 %
Power supply: . . . . . . . . . . 100 – 240 V~,
50 – 60 Hz
Power consumption: . . . . . 15 VA max.
Ambient temperature. . . . . 0 – 40 °C
Dimensions (W × H × D): . 480 × 135 × 370 mm
Weight: . . . . . . . . . . . . . . . 3.7 kg
Subject to technical modification.
GB
1 ⁄ , 45, 78 rpm
3
7