Maintenance And Cleaning; Over-Voltage Protection; Technical Data - Renkforce 1577235 Bedienungsanleitung

Getting Started, Use
Read and follow the chapter "Safety information" carefully.
• Unwind the cable of the power strip completely.
• Plug the earthed mains plug of the outlet strip into a regular earthed mains socket (wall
socket).
• Place the outlet strip in an appropriate place. Use suitable padding to protect valuable sur-
faces against scratches. Lay the cable such that nobody will trip over it.
• For fixed mounting, the side fastening straps can be used.
• Connect the devices to the sockets of the outlet strip.
• With the main on/off switch, switch the power strip on and off:
- O: Off, I: On
- When switched on, the integrated control lamp is lit.
• With the on/off switch for each socket, switch the corresponding socket on and off:
- O: Off, I: On
- When switched on, the integrated control lamp is lit.
• Switch off the socket before unplugging the device.
• Connect USB devices with suitable USB cables to the USB ports (if available). Note the total
current of all USB ports (see chapter "Technical data").

Over-voltage protection

Depending on the product, there is over-voltage protection (see chapter "Technical data").
When the red warning lamp is lit, the over-voltage protection feature is activated.
When the red warning lamp goes out, the over-voltage protection has been triggered. If this
happens, you can continue to use the power strip, but the over-voltage protection is no longer
active.

Technical data

Item no.
Connection data
Total connected load
Earthed mains sockets
Sockets with child protection
Main switch (on/off)
Socket switch (on/off)
Over-voltage protection
USB ports Number
Voltage / Total current
Cable length
Cable type
Ambient temperature
Ambient humidity (relative, non-condensing)
Dimensions (L x W x H)
Weight
1656672
250 V/AC, 50 Hz, 16 A
max. 3680 W
6
yes
yes (two-pole)
yes (single-pole)
yes (9 kA)
2
5 V/DC / max. 2.1 A
1.5 m
H05VV-F 3G1.5 mm²
-10 °C to +50 °C
10 – 90 %
460 x 76 x 44 mm
625 g

Maintenance and cleaning

• This product does not require servicing. This product does not contain any components that
require maintenance. Never attempt to open or disassemble it. Repair or maintenance work
must be done by a technician or a specialist repair centre.
• Before cleaning the power strip, first unplug all devices from it.
Then completely unplug the earthed mains plug of the power strip from the mains socket
(the wall socket).
• A dry, soft and clean cloth is sufficient for cleaning.
• Dust can be easily removed using a soft, clean long-haired brush and a vacuum cleaner.
Never use aggressive detergents, rubbing alcohol or other chemical solutions, as
these could damage the casing or stop the product from functioning properly.
Disposal
Electronic devices are recyclable waste and must not be disposed of in the house-
hold waste. Always dispose of the product according to the relevant statutory regula-
tions.
1577235
250 V/AC, 50 Hz, 16 A
max. 3680 W
6
yes
yes (two-pole)
yes (single-pole)
yes (9 kA)
- -
- -
1.5 m
H05VV-F 3G1.5 mm²
-10 °C to +50 °C
10 – 90 %
460 x 76 x 44 mm
603 g
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method (e.g. photocopying, microfilming or capture in elec-
tronic data processing systems) requires prior written approval from the editor. Reprinting, also in part, is prohibited. This
publication represent the technical status at the time of printing.
© Copyright 2018 by Conrad Electronic SE.
1577236
250 V/AC, 50 Hz, 16 A
max. 3680 W
6
yes
yes (two-pole)
yes (single-pole)
no
2
5 V/DC / max. 2.1 A
1.5 m
H05VV-F 3G1.5 mm²
-10 °C to +50 °C
10 – 90 %
460 x 76 x 44 mm
610 g
*1656672_1577236_1577235_v2_0318_02_jh_m_en_(1)