Renkforce 1577235 Bedienungsanleitung Seite 3

Operating instructions
6-way power strip
Item no. 1577236 / switchable 90° XL USB
Item no. 1577235 / switchable 90° XL with over-voltage protection
Item no. 1656672 / switchable 90° XL USB with over-voltage protection
Intended use
The power strip provides additional mains sockets with protective earth contacts, which can be
used to connect electrical devices.
Depending on the product, USB charging ports are available (see chapter "Technical data").
The power strip has a main on/off switch and an on/off switch for each socket for selective
power management of connected devices.
The product may only be used in dry, enclosed spaces.
The connection data and the maximum permitted total power consumption of all connected
loads can be found in the "Technical data" section.
For safety and approval purposes, you must not rebuild and/or modify this product. Using the
product for purposes other than those described above may damage the product. In addition,
improper use can cause hazards such as a short circuit, fire or electric shock. Read the
instructions carefully and store them in a safe place. Only make this product available to third
parties together with its operating instructions.
This product complies with statutory national and European regulations. All company and
product names are trademarks of their respective owners. All rights reserved.
Delivery Content
• Power strip
• Warning labels (in different languages)
• Operating instructions
Up-to-date operating instructions
Download the latest operating instructions at www.conrad.com/downloads or scan the QR code
shown. Follow the instructions on the website.
Explanation of symbols
The symbol with the lightning in a triangle indicates that there is a risk to your health,
e.g. due to an electric shock.
The symbol with an exclamation mark in a triangle is used to highlight important
information in these operating instructions. Always read this information carefully.
The arrow symbol indicates special information and advice on how to use the
product.
Always follow the instructions in this manual.
Safety information
Read the operating instructions and safety information carefully. If you do
not follow the safety information and information on proper handling in these
operating instruction, we will assume no liability for any resulting personal
injury or damage to property. Such cases will invalidate the warranty/
guarantee.
a) General information
• The unauthorized conversion and/or modification of the product is prohibited for
safety and approval reasons. Do not open/disassemble! Contains no customer-
serviceable parts.
• Maintenance, adjustment or repair work may only be carried out by an expert/
authorised service centre, which is familiar with the hazards involved and the rel-
evant regulations.
• This product is built according to protection class I. It must only be connected to a
mains socket with a protective earth contact.
• The mains outlet used to connect the product must be located close to the product
and easily accessible.
• This product is not a toy and must be kept out of the reach of children. Position the
product so it is out of the reach of children.
• Do not leave the packaging material lying around carelessly as it may be a danger
to children.
• Handle the product with care. Impacts or falls (even from a low height) may dam-
age the product.
• Always comply with the accident prevention regulations for electrical equipment
when using the product in industrial facilities.
• Also observe the safety information and operating instructions of any other de-
vices which are connected to the product.
• If you have questions which remain unanswered by these operating instructions,
please contact us or other technical personnel.
b) Operating location
• This product may only be used in dry, enclosed, indoor areas. It must not become
damp or wet! Never set up the product in the direct vicinity of a bathroom, shower,
bathtub or similar. This may cause a fatal electric shock!
• The product must not be exposed to extremes of temperature, direct sunlight or
strong vibrations.
• Completely unwind the mains cable before use. The power cable must not be
pinched or damaged by contact with sharp edges. Do not place any objects on
the mains cable or allow it to become kinked. Place the mains cable away from
open spaces where it will not present a trip hazard. The mains plug must be easily
accessible. Do not install the mains cable under carpets or the like.
• Do not use the product in environments where there are high levels of dust, flam-
mable gases, vapours or solvents. This may cause a fire or explosion!
c) Handling and use
• The product comes with warning labels in different languages. If the warning la-
bel on the product is not in your language, attach the corresponding label to the
product.
• Never plug in or unplug the product with damp or wet hands. This may cause a
fatal electric shock!
• Never connect the product to the power supply immediately after it has been trans-
ferred from a cold room into a warm one (e.g. during transport). The condensa-
tion that develops in such cases could damage the device or cause an electric
shock! Let the product reach room temperature first. Wait until the condensation
has evaporated ; this may take several hours. Only after this should the product
be plugged into the power supply and put into use.
• Always pull a mains plug on the gripping surface intended for this purpose. Never
unplug the mains plug from a mains socket by pulling the cable!
• Do not overload the socket strip. Observe the maximal permissible total power
consumption of all electrical loads connected as per chapter "Technical Data".
• Do not connect in series! This can lead to an overload! This constitutes a fire
hazard!
• Insert the mains plug on the socket strip into a wall socket. Do not connect other
power strips to this power strip.
• Do not operate while covered! At higher connected loads, the power strip and the
connecting cable may become warm, which can lead to overheating and poten-
tially a fire if covered!
• Volt-free only, if unplugged!
• Do not use the product if it is damaged (e.g., housing or power cable). This may
cause a fatal electric shock!
In this case, dispose of the product in an environmentally correct manner.
• Safe operation can no longer be assumed if:
- there are signs of damage
- the product does not work at all or works poorly (leaking smoke or a smell of
burning, audible cracking noises, discolouration to the product or the adjacent
surfaces)
- the product was stored under unfavourable conditions
- the product was mishandled during transport
• Only use the product in temperate climates. It is not suitable for use in tropical
climates.
• Always pull the mains plug out of the mains socket before cleaning the outlet strip
or when the device will not be in use for a long time.
• Never pour liquids above or near the product. This constitutes a serious fire haz-
ard and may result in a fatal electrical shock.
If liquid does enter the interior of the power strip, immediately isolate the power
strip's mains plug from the mains (turn off fuse/circuit breaker/residual current cir-
cuit breaker for the corresponding circuit). Once you have isolated the power strip
from the mains, unplug it from the mains socket and consult a technician. Do not
continue to use the product.
d) Assembly
• Ensure that no existing cables or pipes (including water pipes) are damaged when
drilling mounting holes or securing screws.