Safety Warning; Maintenance - Vitavia DIANA 9900 Montageanleitung

1. PLEASE READ THESE INSTRUCTIONS CAREFULLY AND COMPLETELY BEFORE ASSEMBLING YOUR GREENHOUSE.
2. Sharp edges and corners can cause injury. Always wear protective glasses, gloves, shoes and headgear when handling the aluminium profiles, glass
and polycarbonate sheets. Broken glass is a safety hazard – always clear up immediately and dispose of with care.
3. The product you have purchased is intended only for the growing of plants and should only be used for this purpose. When used for other purposes we
will take no responsibility.
4. It is recommended that this greenhouse is assembled by two people.
5. Should you encounter difficulties constructing this house, or in positioning the glass or polycarbonate sheets, please contact your retailer
– do not use force!
SITE SELECTION
Always try to select a sunny location, sheltered
from the wind as much as possible.
IMPORTANT
Before assembling your new greenhouse,
please check that all parts in the provided list
are included. Please take each bundle out of
the packaging in order to identify the parts
better.
It is important that the opened bundles do not
get mixed with one another.
If something is missing please contact your
retailer.
NECESSARY TOOLS
Screw drivers (Normal and Crosshead PH2),
10 mm spanner or wrench.

MAINTENANCE

The greenhouse should be thoroughly washed
with a gentle detergent occasionally. Please
check that the detergent used does not react
aggressively with aluminium or the glass fixing
clips.
Ensure that the upper and lower door tracks
are cleaned regularly to avoid a build up of
debris
0 BASE
Important! The base must be exactly square
and level. A zinc-coated steel base is available
as an accessory for all greenhouse models.
(Attention! Only when the greenhouse has to
be located in a very windy and unprotected
location: Drill through both the profile at the
base of the greenhouse and the steel base,
and connect them with nuts and bolts.)
4

Safety Warning

Assembly Instructions
If you would rather construct your own stone
or concrete foundation, please follow the
dimensions specified in diagram 0.
Treated wooden beams at least 18 mm high
and not more then 32 mm wide should be
positioned between the stone/concrete foun-
dation and the aluminium frame, and con-
nected to the foundation with 50 mm long bolts
(not provided).
Foundations must extend down below the frost
level.
All diagrams are shown from the inside
of the house, with the exception of those
enclosed in a double frame, indicating the
outside view.
1. SIDE ELEMENTS
Lay all of the parts on the floor and connect
them loosely.
For Diana 6700, 8300, 9900 & 11500 –
It is necessary with each outside vertical alumi-
nium bar (1032) to include an extra connecting
bolt at this stage. This bolt is required to con-
nect the cross braces (5095), see (1.2).
Loosely connect the corner plate (5091) (1.1).
In step 4 the corner plate bolts must also be
connected to the gable ends.
2. PLAIN GABLE END
Lay all of the parts on the floor and connect
them loosely.
Include two extra connecting bolts in the
vertical bars (5041) and (5042) to connect the
cross braces (2.2) and (2.6). In the vertical bar
(5101) please include only one extra bolt.
3. DOOR GABLE END
Lay all of the parts on the floor and connect
them loosely.
The door runner bars (5047) will be connected
to the horizontal bar (2048). Connect these
loosely from the outside with two nuts and
bolts.
Connect the clips (1013), in order to strengthen
the structure, and the plastic parts (5001) and
(5002) as shown in (3.6) & (3.7) with a bolt.
Please ensure that the clip edge overlaps,
and fixes the vertical bars (5041) or (5042) as
shown.
Please include one extra bolt in the vertical
bars (5041) and (5042).
4A. CONNECTING THE SEPARATE
ELEMENTS
Bolt the side elements to the end elements.
(4.1), (4.2) & (4.3)
Assemble the ridge bar and then the corner
plates (1092) on the gable ends (4.4) & (4.5).
Loosely connect door runner supports (5043)
to the door runner bars (5047) and to the ga-
ble end, using bolt (1005) and spacer (1010)
(4.6).
4B. CONNECTING THE SEPARATE
ELEMENTS
Connect the roof glazing bars (5055) between
the eaves (4.7) and the ridge bar (4.8).
Insert extra bolts into each glazing bar depen-
ding on which house you have bought. The
number is indicated in a circle on each bar and
to be read beginning from both ends.
Please also decide at this point where the roof
vents will be located and adjust the extra bolts
to match.
The roof braces (2057) (4.9) and the cross
braces (5049) (4.11) & (4.12) can now be con-
nected.
Now position your greenhouse on the
prepared base / foundation and connect
006.00.0811