Herunterladen Inhalt Inhalt Diese Seite drucken

Conrad 97 52 21 Bedienungsanleitung Seite 3

Inhaltsverzeichnis

Werbung

Verfügbare Sprachen

Verfügbare Sprachen

O P E R A T I N G I N S T R U C T I O N S
Network audio/video Adapter
Item-No. 97 52 21
Intended Use
The product is used to operate a monitor over a network (10/100 MBit). This allows the monitor to
be operated on several computers (but only in turn; you can only connect one computer to the
Network audio/video Adapter at a time).
It also integrates a USB2.0 hub with 2 ports and a USB sound card with headphone and microphone
inputs.
The Network audio/video Adapter can be directly connected to one of the computers using the 4
control buttons, to monitor them for example.
The product can alternatively be connected directly to a single computer via the USB port if the
network operation is not possible or not required.
The power is supplied from the wall plug transformer included in the delivery.
This product complies with the applicable National and European requirements. All names of
companies and products are the trademarks of the respective owner. All rights reserved.
Package Contents
• Network audio/video Adapter
• Wall plug transformer
• USB Connection Cable
• CD with driver/software
• Operating Instructions
Safety Instructions
The warranty will be void in the event of damage caused by failure to observe
these safety instructions. We do not assume any liability for any consequential
damage!
We do not accept liability for damage to property or personal injury caused by
improper handling or non-compliance with the safety instructions. The warranty
will be void in such cases.
• The unauthorised conversion and/or modification of the product is inadmissible
because of safety and approval reasons (CE). Do not open/disassemble! It does not
contain any internal parts that need to be adjusted or maintained by you.
• This product is not a toy, it is not suitable for children. Children are not aware of the
potential dangers involved when using electrical devices.
• The design of the wall power supply complies with IEC Protection Class II (double
insulated electrical appliances).
• Only connect the wall plug transformer to a standard mains socket connected to the
public supply. For the permitted operating voltage for the mains adapter, please refer
to the chapter "Technical Data" at the end of this operating manual.
• Never plug in, or remove, the wall plug transformer when your hands are wet!
• The product must not get damp or wet, it is only intended for use in dry, indoor
locations.
Furthermore, protect the product from direct solar radiation, strong heat (>35°C), cold
(<0°C), dust and dirt, splashes and dripping water, vibrations or mechanical loads.
• When the product is taken from a cold room to a warm one (e.g. during transport),
condensation may be produced. This could damage the product. This might cause a
lethal electric shock!
Therefore, you should allow the product to warm up to room temperature before using
it or connecting the wall plug transformer to an electric socket. This may take several
hours.
• Do not operate the product if it is damaged.
Do not touch the wall plug transformer, if it is damaged. First, switch off at the mains
socket where the product is connected (e.g. with the circuit breaker), and then
carefully unplug the wall plug transformer from the mains socket. Disconnect the
plug-in transformer from the device. Never operate the product with a damaged wall
plug transformer! There is a risk of a life-threatening electric shock!
• Do not leave packing materials unattended. They may become dangerous playthings
for children.
• In commercial institutions, the accident prevention regulations of the Employer's
Liability Insurance Association for Electrical Systems and Operating Materials are to
be observed.
• In schools, educational centres, hobby and self-help workshops the operation of the
product is to be supervised by trained employees.
• Handle the product with care, it can be damaged by impacts, blows, or accidental
drops, even from a low height.
• If you have any questions that are not answered in this instruction manual, please
contact our technical support centre or consult a professional.
Connection via Network or USB
www.conrad.com
The product offers two different operating modes. Only one of them may be used simultaneously:
• Operation via network
Version 11/10
The product is connected to the network switch or router via a 1:1 connected network cable
°
(10/100 MBit network).
Each PC connected to the network can access the monitor, the two USB ports and the integrated
sound card on the Network audio/video Adapter - However, only one PC at a time.
Example: A video projector installed in a training classroom can be used by 20 PCs without having
to plug again the cables.
The four buttons on the Network audio/video Adapter are used to commutate the four PCs
directly. This can be used to monitor four server PCs in turn for example.
• Operation via USB
If an operation over the network is not possible or required, the Network audio/video Adapter can
also be connected directly to a single PC via the USB port. It then works as a conventional USB
graphic card with integrated 2-port USB hub and integrated sound card.
Operation via network
• Connect your monitor with the DVI port of your Network audio/video Adapter. If you want to
connect an analogue VGA monitor, please use the supplied VGA-DVI adapter.
• Connect the Network audio/video Adapter to your network switch or router using a 1:1 connected
network cable.
• Connect the low voltage plug of the supplied wall plug transformer to the Network audio/video
Adapter and plug it into a mains socket.
• Insert the included CD into one of the computers connected to the network. If the installation pro-
gram on the CD does not start automatically, start the "Setup.exe" program in the main directory
of the CD.
• Click on "Auto Installation......" and follow all instructions.
During installation, it can happen that the image disappears, flashes or that the resolution
changes automatically on the monitor directly connected to the computer. Wait until the
installation is complete! If you are not connected as an administrator on the operating system,
you may still have to confirm some Windows messages accordingly.
• Windows may need to be restarted after completing the installation.
• A new icon "Launch Networking USB Server", or similar appears on the desktop, through which
the software can be started.
• Depending on your operating system (e.g. Windows 7), a warning message is displayed,
indicating that the software tries to access the network.
• After starting the software, click on "Search" to
search for the Network audio/video Adapter on the
network.
If found, click on it and select "Connect Device" to
connect the computer to the Network audio/video
Adapter, see Figure on the right.
• If desired, connect a USB keyboard or USB mouse
with the Network audio/video Adapter. The USB ports can also be used for other products, e.g.
USB flash drive, etc.
Headphones, microphone or headset can now be connected to the Network audio/video Adapter.
All devices are now available on the PC which is connected to the Network audio/video Adapter.
• If the software should start automatically at
Windows start, you can select the function "Run
this application when PC starts up" in "Options"
(check mark appears).
Please note:
The included software must be installed on each PC that should have access to the
Network audio/video Adapter. Without software installed, the operation is not possible.
Important for USB operation: First install the enclosed software! Then connect the
Network audio/video Adapter to the USB port of your PC.
The software installation is required on each PC that should have access to the
Network audio/video Adapter!
You must allow this access, otherwise no connection can be established with the
Network audio/video Adapter!

Werbung

Inhaltsverzeichnis
loading

Inhaltsverzeichnis