Renkforce 1362922 Bedienungsanleitung Seite 3

G Operating instructions
Ceiling motion detector 360° with corner base
Item no. 1362922
Intended use
The PIR sensor integrated in the motion detector responds to temperature changes within the
detection range, e.g. if a person, a large animal or a car enters the detection area.
For this reason, the motion detector can be used for monitoring entrances, driveways, staircases,
etc.
The motion detector' output, for example, can be used for controlling a light or another powered
device. Please refer to the section "Technical data".
The motion detector can be mounted on either a vertical wall, a vertical building corner (with the
provided corner base) or on the room ceiling.
Any other use than that described above may damage the product. Moreover, this may give rise to
hazards such as short-circuiting, fire, electric shock, etc. No part of the product may be modified
or converted!
Always observe the safety instructions in these operating instructions. Please read the operating
instructions carefully and keep them.
This product complies with the applicable National and European requirements. All names of com-
panies and products are the trademarks of the respective owner. All rights reserved.
Package contents
• Motion detector
• Corner base
• Mounting material (screws, dowels)
• Cover for PIR sensor (for limiting the detection area)
• Operating instructions
Explanation of symbols, inscriptions
This symbol indicates a health hazard, e.g. electric shock.
The exclamation mark indicates specific risks associated with handling, function and
use.
The "arrow" symbol indicates special tips and operating information.
IP55
The product is designed for operation outdoors.
The product complies with the protection class II.
Safety instructions
R ead the complete operating manual carefully before using the product as it contains
important information about the correct installation and operation.
T he warranty will be void in the event of damage caused by failure to observe these
safety instructions! We do not assume any liability for any consequential damage!
N or do we assume any liability for material and personal damage caused by improper
use or non-compliance with the safety instructions! The warranty will be void in such
cases!
Caution!
T his product may only be installed by a qualified technician (e.g., an electrician) who
is familiar with the relevant regulations (e.g., VDE, German electrical wiring regulati-
ons)!
I mproper work, carried out on the mains voltage, endangers not only your own life but
also the life of others!
I f you do not have the expertise required for the installation, do not install it yourself
but ask a qualified technician.
• The unauthorised conversion and/or modification of the product is not allowed for
safety and approval reasons (CE).
• The product is not a toy and must be kept out of the reach of children! There is the
risk of a fatal electric shock!
• The product may only be operated on the mains voltage (see section "Technical
data"). Never try to operate the product at another voltage as this will cause its de-
struction.
• The product is constructed according to protection class II.
• During installation, all poles must be disconnected from the mains voltage (e.g., via
RCD).
• The product may be mounted in indoor and outdoor areas (protection type IP55).
Please refer to the section "Mounting".
• Only use the product when it is firmly mounted/steady.
• Do not use the motion detector in rooms, or in adverse ambient conditions, where
combustible gases, vapours or dust are or may be present! There is a risk of explo-
sion!
• The product must not be exposed to extreme temperatures, strong vibrations or
heavy mechanical loads.
• Never direct a jet of water (e.g. for cleaning) from a garden hose, high-pressure
cleaner, or similar onto the motion detector!
• If you have reason to assume that safe operation is no longer possible, disconnect
the product immediately and secure it against inadvertent operation. Let an expert
check the product.
A safe operation can no longer be assumed, if:
- the product shows visible signs of damage
- the product does not work at all or well (flickering light, leaking smoke or a smell of
burning, the light flickers, audible cracking noises, discolouration to the product or
the adjacent surfaces.)
- the device was stored for a longer period of time in unfavourable conditions
- it was exposed to heavy loads during transport
• Do not leave packaging material carelessly lying around since it could become a
dangerous plaything for children.
• In commercial institutions, the accident prevention regulations of the Employer's Li-
ability Insurance Association for Electrical Systems and Operating Facilities are to
be observed!
• If you have any questions that are not answered in this manual, please contact our
technical service or another specialist.
Preparations for installation
T he motion detector may be installed only by a qualified technician (e.g. electrician)
who is familiar with the relevant regulations (e.g. VDE, German electrical wiring re-
gulations)!
I mproper work, carried out on the mains voltage, endangers not only your own life but
also the life of others!
I f you do not have the expertise required for the installation, do not install it yourself
but ask a qualified technician.
• Without fail, pay attention to the correct mounting position for the motion detector; it must only
be mounted so that the hemispherical PIR sensor points downwards.
If this mounting position is not observed, water might penetrate the motion detector;
danger of a fatal electric shock!
• Only install the motion detector on a stable surface, e.g. brickwork. Depending on the surface,
suitable screws and plugs should be used.
• The motion detector must be installed and used out of the reach of children.
• The power supply line for the motion detector must be protected by a 10/16A fuse on the build-
ingside sub-distribution. An earth leakage circuit breaker must be installed before this (FI pro-
tective switch).
• The motion detector must be voltage-free during installation.
Turn the power off and remove the electric circuit fuse or switch off the circuit breaker. Secure
it against unauthorised reconnection, e.g., with a danger sign.
Furthermore, turn off the earth leakage circuit breaker in order to disconnect all the poles of the
mains supply.
• Check that the mains connection is free of current e.g. with an appropriate tester.
Function of the motion detector
The PIR sensor integrated in the motion detector responds to temperature changes within the
detection range, e.g. if a person or an animal, with a temperature different from the background,
enters the detection area.
To ensure optimum detection, the motion detector must be placed so that the object to be detected
does not approach the motion detector directly but rather passes through the detection area from
left to right or vice versa. Keep this in mind, when installing the product.
The triangular detection area can be adjusted by turning the hemispherical PIR sensor (clicking
noises can be heard during turning due to an integrated catch).
The range for detecting motion is determined by several factors:
• The motion detector's installation height
• The temperature difference between the moving object and the background (ambient)
• The size of the object
• Distance of the object from the motion detector
• Direction and speed of the movement
• Ambient temperature