Repeat Play; Random Play - Bigben Interactive TD95 Bedienungsanleitung

Repeat play

You can listen the desired tracks or all the track repeatedly. Press Repeat/Random button once (3), the
Repeat/Random LED indicator (23) will flash fast and the current track will repeatedly playback. Press this button
again, the Repeat/Random LED indicator (23) will flash slowly and whole disc will repeatedly playback.

Random play

You can listen all the tracks in a random order by this function, press and hold the Repeat/Random button (3), the
Repeat/Random LED indicator (23) and Play LED indicator (22) will light up, system will start to playback in random
mode automatically.
Playback of MP3 song via USB storage media or memory card
Connecting
The system is able to decode and playback all MP3 file which stored in the memory media with USB connecting port or
SD/MMC memory card.
1. Set function switch (12) at USB/SD mode and then press USB/SD button (on remote control)
to select " USB or card " mode. The USB indicator (17) or SD card indicator (19) will light up.
2. Plug-in the USB plug with the face up & make sure it going into completely or insert the
memory card in the direction of the arrow as shown in the label on the upper side of the
memory card slot . Insert straight without bending.
Connecting the USB upside down or backwards could damage the audio system or
the storage media (USB thumb drive / SD/MMC card). Check to be sure the direction
is correct before connection.
3. The system will start reading the storage media and playback automatically after connecting.
4. Repeat the same playback procedure as playing CD/MP3 disc as above
Remark
- The system can detect and read the file under MP3 format only though the USB port.
- If connect the system to MP3 player via the USB socket, due to variances in MP3 encoding format, some
MP3 player may not be able to play via the USB socket. This is not a malfunction of the system.
Encoding of CD/phono into MP3 file
The system is able to encode normal cd or turntable to MP3 format and recording at memory media with USB
connecting port or SD/MMC card.
A) CD encoding
I) Encoding 1 track
1. Perform normal playback of the CD track you want to encode & record,
2. Press " Record " button (2) during the playback of the desire track, the Record LED indicator (24) will flash. Press
the Record button (2) again to confirm record, the Record LED indicator (24) will change to light up and USB LED
indicator (17) will flash, system will go back to the beginning of the current track and start to encode.
3. After completing of encoding, unit will stop record and continue playback the CD.
II) Encoding 1 disc
1. Place a CD with the printed side facing up inside the tray & then close the CD tray.
2. Press " Record " button (2) in CD stop mode, the Record LED indicator (24) will flash. Press the Record button (2)
again to confirm record, the Record LED indicator (24) will change to light up and USB LED indicator (17) will
flash, system will start to playback the CD from first track and perform encode.
3. After completing of encoding whole disc, unit will stop record automatically.
Remark:-
- The recording speed is 1:1 and according to the actual plying time of the CD track
- The recording format is preset at – MP3
- No song title will be recorded during encoding mode
- To interrupt the recording, Record button (2) to stop encoding.
III) Copying of MP3 file
If putting a MP3 disc instead of a CD-disc, the system will copy the files to the USB or SD/MMC card. The operation
procedures is same as CD encoding as stipulate on above, and the system will switch to copying mode instead of
playback mode if MP3 file being read.
Remark:
- The system will store the file to USB source first if both USB and SD slot are being occupied by storage media.
- If press the " Record " button (2) during playback of USB or SD source, the file will copy from USB to SD or SD to
USB.
bit rate : 128 kbps, sampling rate : 44.1khz
5