Remote Control; Flight Control - Revell Control ACROBAT XP Bedienungsanleitung

1 helICOpTer
1A Rotor blades 1B Flybar
1D Battery compartment

2 reMOTe COnTrOl

2A Display
2B Trim for rotation
2C Control for thrust and rotation
2D Turbo button
2E Power LED
2F Antenna
3 InserTIng BaTTerIes (reMOTe COnTrOl)
3A To open the battery 3B Insert 6 x 1.5 V AA batteries
compartment, slide the and pay attention to the
cover down.
polarity specifications, as
indicated in the battery
compartment.
4 ChargIng The helICOpTer
Attention: The battery and motor must cool down for 10 to 15 minutes before
charging and after every flight. Otherwise they can be damaged. The charging process
must be constantly monitored. Always ensure that the charging process takes place on
a fireproof surface in a fire-resistant environment.
•Unplug the battery from the model and switch off the remote control. Connect the
USB cable to the charger and insert it in an available USB port. (4A).
• Now insert the battery into the charger from above. Pay attention to the polarity.
The groove of the battery fits into the recess of the holder (4B). The battery must
be gently inserted into the charging socket – DO NOT USE FORCE. If the battery is not
correctly inserted into the charging socket, the battery may become damaged and,
under certain circumstances, cause injury.
• The LED on the charger will light up red when charging begins.
• The charging process lasts approx. 30 minutes and must be continuously monitored.
The red LED on the charger goes out as soon as the charging process is finished.
• Disconnect the battery from the charger and disconnect the charger from the USB
port once charging is complete.
After a charge time of approx. 30 minutes the Helicopter can fly for
approx. 5-7 minutes.
Warning notice: The battery does not normally heat up while charging. If it should
become warm or even hot and/or changes to the surface begin to appear, immediately
discontinue the charging process!
14
1C Tail rotor
2G ON/OFF switch
2H Trim for forwards and backwards
2I Control for forwards/backwards
and sideways
2J Trim for sideways
2K Battery compartment cover
3C Slide the cover up
and close.
5 sTarT preparaTIOn
The helicopter must be switched on first in order to connect it to the remote control.
For this purpose, insert the battery in the battery holder from behind. Do not use force
and ensure the correct polarity (5A). The groove of the battery fits into the recess of
the holder.
After the battery has been inserted into the model, a small red LED inside the
helicopter blinks for a duration of about seven seconds. Switch on the remote control
during these seven seconds. The helicopter may not be moved during this time. The
thrust controller must point down before the remote control is switched on (5B). The
helicopter activates after about five seconds.
6 TrIM aDJusTMenT OF The COnTrOl
The correct trimming is a basic requirement for achieving fault-free flying from the
helicopter. Its adjustment is simple, but it requires some patience and a feel for it.
Please observe the following instructions precisely: Carefully move the thrust control
up and raise the helicopter approximately 0.5 to 1 metre in altitude.
6A If the helicopter automatically moves slowly or quickly to the left or right ...
gradually press the trim for sideways flight (2J) in the opposite direction.
6B If the helicopter moves by itself slowly or quickly around its own axis ...
press the trim adjustment for rotation (2B) incrementally in the opposite direction.
6C If the helicopter automatically moves slowly or quickly forwards or
backwards ...
gradually press the forwards/backwards trim (2H) in the opposite direction.

7 FlIghT COnTrOl

Note: Only minimal corrections of the controls are necessary for a smoothing flying
behaviour of the helicopter! The direction information applies if the helicopter is viewed
from behind. If the helicopter is flying towards the pilot, it must be moved in the
opposite direction.
7A Take off or increase altitude by carefully moving the control for thrust and
rotation (2C) forward.
7B Land or decrease altitude by moving the control for thrust and
rotation (2C) backward.
7C Fly forward by moving the controller for forward/backward and sideways (2I)
flight carefully forward.
7D Fly backward by moving the controller for forward/backward and sideways (2I)
flight carefully backward.
7E Fly to the left by moving the controller for forward/backward and sideways (2I)
flight carefully to the left.
7F Fly to the right by moving the controller for forward/backward and sideways (2I)
flight carefully to the right.
7G Turn helicopter around to the left by moving the controller for thrust and rotation
(2C) to the left.
7H Turn helicopter around to the right by moving the controller for thrust and rotation
(2C) to the right.
15