Ego Power+ LM2020E Bedienungsanleitung Seite 13

◾
The handle is locked into one of the three operating
positions, see ADJUSTING THE FOLDABLE HANDLE.
◾
The side rails are fully extended (Fig. P).
◾
Both green handle-locking clamps are securely closed
(Fig. Q).
Q-1 Indication Line
CAUTION:
Do not attempt to override the operation
of the safety button and bail switch.
To Start
1) Attach the battery pack to the mower, insert the safety
key into the key slot and close the battery cover (Fig. O).
2) According to Fig. R, depress the safety button down.
3) With the switch button depressed, pull the bail switch
upward to the handle and release the safety button
(Fig. S).
To Stop
1) Fully release the bail switch.
2) The electric brake in the Automatic Braking
Mechanism will stop the blade rotation within 3
seconds of the bail switch release.
VARIABLE-SPEED SELF-PROPEL SYSTEM (only
model LM2020E-SP)
LM2020E-SP mower is equipped with variable-speed
self-propel capability. This system is independent of the
blade On-Off switch; it is not dependent on blade rotation.
To operate the system without blade rotation, pull the
self-propel trigger to the handle.
To turn the self propel off, release the self-propel trigger.
The system has variable speed. To increase the speed,
move the self-propel speed-control lever forwards. To
decrease the speed, move the self-propel speed-control
lever backwards (Fig. T).
To operate with the blade rotating for cutting:
1. Start the mower.
2. While holding the bail switch against the handle with
left hand, pull the self-propel trigger to the handle
with your right hand.
3. Hold both the bail switch and the self-propel trigger
simultaneously against the handle with your right
hand and use your left hand to adjust the self-propel
speed-control lever to choose a proper speed.
WARNING:
To reduce the risk of injury, never attempt
to override the operation of the switch or self propel system.
Use the self propel for its intended purpose only.
56 VOLT LITHIUM-ION CORDLESS MOWER — LM2020E / LM2020E-SP
LED HEADLIGHTS (Fig. A-13)
Press the switch button (Fig. C-22) to turn on/off the LED
headlights in the front of the battery compartment.
POWER INDICATOR ON THE MOWER (Fig. U)
The mower is equipped with a power indicator to indicate
the charge level of the battery pack and the working
status of the mower. The power indicator will illuminate
when the blade is rotating or when the LED headlights are
turned on.
Power
Indicator Meaning
on Mower
Mower is working
Shining properly; battery
green has at least 15%
of its charge
Shining red Low battery
The battery is
Flashing red
nearly depleted
The mower or the
Shining
battery pack is
orange
overheated
Flashing The mower is
orange overloaded
MOWER OVERLOAD PROTECTION
To prevent overload conditions, do not try to remove too
much grass at one time. Slow down your cutting pace or
raise the cut height.
Your mower has built-in overload circuit protection. When
the mower is overloaded, the motor will stop and the
power indicator on the mower will flash orange. Remove
the battery pack from the mower. Check to see if grass
has collected beneath the deck and clear it if necessary,
then install the battery and restart the mower.
BATTERY HIGH TEMPERATURE PROTECTION
The battery pack will generate heat during operation. The heat
dissipates more slowly in hot weather. If the battery tempera-
ture exceeds 70°C during operation, the protection circuit will
immediately turn off the mower to protect the battery pack
from damage. The power indicator on the mower will shine
orange and the LED on the battery will flash orange. Release
the bail handle, wait until the battery pack cools down to
approximately 67°C , then restart the mower.
EN
Action
N/A
Stop the mower and
charge the battery pack
Stop the mower and
charge the battery pack
Remove the battery
from the mower, move
them to the shade and
cool them at least 15
minutes
Slow down your pace
or raise up the cut
height to decrease
the load
13