Charging Process - Revell Control STUNTCAR KICK FLIP Bedienungsanleitung

4 ChargINg proCeSS

There are two options for charging the
vehicle and in both cases the vehicle and
the remote control must be switched off.
Attention: The battery and motor must
cool down for about 10 to 30 minutes
before charging and after every flight.
Otherwise they can be damaged. The
charging process must be constantly
monitored. Always ensure that the
charging process takes place on a fire proof
surface in a fire­resistant environment.
Transmitter:
4A The charging cable is concealed
beneath a flap on the bottom side of the
remote control. This cable is inserted into
the charge socket of the car. The charge
LED on the remote control illuminates
during the charging process. If it goes out,
the charging process is complete and the
charging cable must be unplugged.
5 STarT preparaTIoN
Roll bar:
A roll bar is included with the stunt car. It
has already been provided with double-
sided adhesive table. Remove the protective
film on both sides of the adhesive tape.
5A The open side of the adhesive tab
must face backwards. Begin by adhering
one side.
5B Then bend the other side of the roll bar
over the car and adhere it to the already
fastened end.
14
USB charging cable:
4B Alternatively, the car can also be
charged using the accompanying USB
charging cable. The car must be switched
off for this process as well. When inserting
the charger into a USB port, a red ready
LED illuminates. This LED goes out during
the charge process and illuminates again
when the battery is fully charged.
The battery is full after a charging time of
about 20-40 minutes. The vehicle can be
driven for about 7-10 minutes with a fully
battery.
Warning notice: The LiPo battery does
not normally heat up while charging.
However, if it should become warm or
even hot and/or show signs of changes in
the surface, the charging process must be
immediately discontinued!
Driving:
First move the switch on the underside of
the model to ON ( 5C ) then set the switch
on the remote control (5D) to ON. It is
actually important that the car is switched
on first, and then the remote control. When
switching off, always switch off the vehicle
first (cf. 5C), then the remote control
(cf. 5D)! Otherwise, a drive command can
accidentally be triggered, causing the
vehicle to drive away on its own, which
can lead to considerable damage.
6 STeerINg TrIM adjuSTMeNT
The correct trim is a basic requirement for fault-free driving behaviour from the
vehicle. Adjusting the trim is easy, but it requires a little patience and a feel for it.
Please follow the following instructions precisely:
When the vehicle pulls to the left or right while driving without steering...
use the trim wheel on the remote control (6A) to correct the wheel alignment by
turning it in the opposite direction.
7 vehICle CoNTrol
7A In order to drive forwards, pull the lever
for forward and reverse travel backwards.
7B In order to drive backwards, push the
lever for forward and reverse travel for-
wards. Gentle braking can also take place
in this manner during forward travel.
INSTruCTIoNS For SaFe drIvINg
GENERAL DRIVING TIpS:
• Always maintain visual contact with the vehicle and do not look at the remote control!
• On initial driving attempts, there is a general tendency toward excessive movements
of the controls. Make sure that you have sufficient room.
After a crash, always release the speed control immediately in order to prevent
damage to the electronics.
THE SUITABLE DRIVING ENVIRONMENT:
The location in which the vehicle is driven should fulfill the following criteria:
1. It should be a location in which there is as much open area as possible, without
disruptive obstacles.
2. Make absolutely sure when starting that there are no people or animals in the
immediate vicinity.
3. Always watch the vehicle so that it does not drive into the operator, other people or
animals and injuries them.
7C In order to drive along curves, move
the steering wheel in the corresponding
direction (right in clockwise motion, left
in anticlockwise motion).
7D The end speed can be influenced with
the rocker lever on the upper side of the
remote control. If the rocker is pushed
upwards, the car becomes faster.
15