Herunterladen Inhalt Inhalt Diese Seite drucken

Alarm Function; Troubleshooting - Conrad Jumbo Bedienungsanleitung

Funk kalender tischuhr
Vorschau ausblenden Andere Handbücher für Jumbo:
Inhaltsverzeichnis

Werbung

Verfügbare Sprachen

Verfügbare Sprachen

12/24 hour display
• Press the +12/24 (B1) button in order to change between a 12h- and a 24h-display.
Calendar overview
• Press the button S (B4), and F (B6), respectively, in order to display the following or the pre-
vious months in the calendar overview (A6).
• Press the HOME (B5) button, to return to the present calendar overview (A6).
Reminder
Up to eight deadlines can be saved.
The day of the deadline is marked with a flashing frame in the calendar overview (A6).
Programming
• Press the button MODE/SET (B2) until the display shows "EVENT".
• Press and hold the button MODE/SET (B2) until the number display is flashing below EVENT.
• Set the numbers (EVENT 1-8) using the buttons +12/24 (B1) and -°C/°F (B3).
• Press the button MODE/SET (B2) again. The month display blinks.
• Then set the month and the day for the deadline reminder as described above.
• Press the MODE/SET (B2) button again to save these settings.
Display
• Press the button MODE/SET (B2) twice until the display shows "EVENT" to review a saved
deadline.
• Using the buttons +12/24 (B1) and -°C/°F (B3) the saved deadlines can now be browsed
through.
• If there is a deadline in the current month this actual day will be marked in the calendar
overview (A6) by a flashing frame.
• If there is a deadline for the current day EVENT is flashing in the display.

Alarm function

The watch is equipped with a alarm function.
• Press the button MODE/SET (B2) until the display shows "AL".
• Press and hold the button MODE/SET (B2) until the hours display of the alarm time is
flashing.
• Set the hours using the buttons +12/24 (B1) and -°C/°F (B3).
• Press the button MODE/SET (B2) again. The minute display blinks.
• Set the minutes using the buttons +12/24 (B1) and -°C/°F (B3).
• Press the MODE/SET (B2) button again to save these settings.
• In order to turn on/off the alarm function, set the switch ALARM ON/OFF (B8) to position ON.
• With the activated alarm function the alarm symbol (A2) appears in the display.
• To activate the snooze function during alarm SNOOZE/LIGHT (B7) button. The alarm signal
is turned off and will be released again after approx. 5 minutes.
• The snooze function can be activated up to 7 times.
• In order to turn off the alarm signal press any button.
• To turn off the alarm function totally set the switch ALARM ON/OFF (B8) to position OFF.
Temperature Display
• The room temperature is shown lower on the display.
• You can switch the temperature display between C° and F using the -°C/°F button (B3).
Display Light
• Press the SNOOZE/LIGHT (B7) button to switch on the display light for about 5 seconds.

Troubleshooting

By purchasing this Jumbo Radio Table Calendar Watch, you have acquired a product with state
of the art design that is operationally reliable.
Nevertheless, problems or faults may occur.
Which is why we would like to describe here how to solve any problems:
The clock does not synchronise or reception is poor:
• The distance to the DCF transmitter is too long or restricted by geographical conditions.
• Relocate the product, switch off interfering devices such as TV sets, computers or microwave
ovens.
• Avoid a location in the vicinity of large metal surfaces, which may shield the radio signals.
Windows with a vapour deposited metal layer can also influence the signal reception.
• Place the clock near a window for synchronisation, and align the front or back side in the direc-
tion of Frankfurt (Germany).
• Leave the clock switched on overnight to avoid atmospheric interference.
The displayed temperatures are not correct:
• The clock is exposed to direct sunlight.
• The watch is too close to a heat source (heater, electronic device etc.)
The display shows confused symbols or nothing is displayed at all:
• Press the RESET (B9) button with a pointed object (e.g. a ball pen tip). By doing so, the
installed micro processor will be reset.
The device no longer reacts to input:
• During DCF synchronisation the buttons are locked. Wait until the synchronisation has been
finished or stop it manually.
The display has black spots:
• Pressure has been applied to the display. The black spots will disappear again. This can take
a very long time, depending on the ambient temperature.
Maintenance and Care
Apart from a battery change, the device is maintenance-free. Clean the exterior of the device
only with a soft, dry cloth or a small brush.
Never use caustic cleaning agents or chemical solutions as the surface of the case could be
damaged.
Do not apply pressure to the sensitive surface of the display.
Disposal
Please dispose of the product, when it is no longer of use, according to the current
statutory requirements.
Disposal of flat batteries/rechargeable batteries
As the end user, you are required by law (Battery Ordinance) to return
all used batteries/rechargeable batteries; disposal of them in the
household waste is prohibited.
Contaminated batteries/rechargeable batteries are labelled with these
symbols to indicate that their disposal in the domestic waste is forbid-
den. The symbols for the relevant heavy metals are: Cd = cadmium,
Hg = mercury, Pb = lead. You can return used batteries/rechargeable
batteries free of charge to any local authority collection point, to our
stores or to any other store where batteries/rechargeable batteries are
sold.
You thus fulfil your statutory obligations and contribute to the protection of the environment.
Technical Data
Operating voltage
Batteries
Battery life
Time protocol
Temperature measuring range:
Deadline memory
Calendar overview
Dimensions
Weight
Declaration of conformity
We, Conrad Electronic, Klaus-Conrad-Straße 1, 92240 Hirschau, hereby declare that this prod-
uct adheres to the fundamental requirements and the other relevant regulations of Directive
1999/5/EC.
You can find the declaration of conformity at www.conrad.com.
These operating instructions are a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240
Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or
the capture in electronic data processing systems require the prior written approval by the editor.
Reprinting, also in part, is prohibited.
These operating instructions represent the technical status at the time of printing. Changes in
technology and equipment reserved.
© Copyright 2009 by Conrad Electronic SE.
3V=
2 x 1.5V Mignon battery (AA)
Order No: 65 25 02 (order 2x)
approx. 2 years
DCF
0 to +50 °C
8 Events
1900-2099
189 x 118 x 57mm
320g

Werbung

Inhaltsverzeichnis
loading

Inhaltsverzeichnis