Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
Operating instructions
Bar code scanner 1D iDC9507A wireless
Item no. 1277813
Intended use
The product is used for contact-free reading of bar codes. The data are transferred wirelessly
via Bluetooth
. The receiver must therefore have a Bluetooth
®
The bar code scanner functions in a manner similar to a wireless keyboard. It transmits the data
contained in the scanned bar code as text to the receiver (e.g. a PC or a tablet), which then
shows this information in the already running software (spreadsheet, text editor).
The built-in battery provides the required power. It charges automatically as soon as the
scanner is connected to a USB port or a USB power supply using the provided mini USB cable.
It is intended for indoor use only. Do not use it outdoors. Contact with moisture, e.g. in
bathrooms, must be avoided under all circumstances.
For safety and approval purposes, you must not rebuild and/or modify this product. If you use
the product for purposes other than those described above, the product may be damaged.
In addition, improper use can cause hazards such as short circuiting, fire, electric shock etc.
Read the instructions carefully and keep them. Make this product available to third parties only
together with its operating instructions.
This product complies with the statutory national and European requirements. All company
names and product names are trademarks of their respective owners. All rights reserved.
Bluetooth
is a registered trademark of Bluetooth SIG, Inc.
®
Delivery content
• Bar code scanner
• Mini USB cable (for charging)
• Wrist loop
• Operating instructions
Latest operating instructions
Download the latest operating instructions via the link www.conrad.com/downloads or scan the
QR code shown. Follow the instructions on the website.
Explanation of symbols
The lightning symbol inside a triangle is used when there is a potential risk of
personal injury, such as electric shock.
An exclamation mark in a triangle indicates important instructions in this operating
manual that absolutely have to be observed.
The arrow symbol indicates specific tips and advice on operation.
Safety instructions
Read the operating instructions carefully and especially observe the safety
information. If you do not follow the safety instructions and information
on proper handling in this manual, we assume no liability for any resulting
personal injury or damage to property. Such cases will invalidate the warranty/
guarantee.
a) General
• The device is not a toy. Keep it out of the reach of children and pets.
• Do not leave packaging material lying around carelessly. This may become
dangerous playing material for children.
• Protect the product from extreme temperatures, direct sunlight, strong jolts, high
humidity, moisture, flammable gases, vapours and solvents.
• Do not place the product under any mechanical stress.
• If it is no longer possible to operate the product safely, take it out of operation and
protect it from any accidental use. Safe operation can no longer be guaranteed
if the product:
- is visibly damaged,
- is no longer working properly,
- has been stored for extended periods in poor ambient conditions or
- has been subjected to any serious transport-related stresses.
• Please handle the product carefully. Jolts, impacts or a fall even from a low height
can damage the product.
• Also observe the safety and operating instructions of any other devices which are
connected to the product.
• Never look into the light beam of the barcode scanner with the naked eye or with
optical instruments. There is risk of eye damage!
• Do not point the laser beam at mirrors or other reflective surfaces. The uncontrolled,
reflected beam may strike people or animals.
interface.
®
• Consult an expert when in doubt about operation, safety or connection of the
device.
• Maintenance, modifications and repairs are to be performed exclusively by an
expert or at a qualified shop.
• If you have questions which remain unanswered by these operating instructions,
contact our technical support service or other technical personnel.
b) Rechargeable batteries
• The rechargeable battery is permanently built into the product and cannot be
replaced.
• Never damage the rechargeable battery. Damaging the casing of the rechargeable
battery might cause an explosion or a fire!
• Never short-circuit the contacts of the rechargeable battery. Do not throw the
battery or the product into fire. There is a danger of fire and explosion!
• Charge the rechargeable battery regularly, even if you do are not using the
product. Due to the rechargeable battery technology being used, you do not need
to discharge the rechargeable battery first.
• Never charge the rechargeable battery of the product unattended.
• When charging, place the product on a surface that is not heat-sensitive. It is
normal that a certain amount of heat is generated during charging.
Getting started
The bar code scanner works with practically any device (computer, notebook, mobile, tablet,
etc.). The important thing is that the device have a Bluetooth
operating systems are supported, please see the technical data of these instructions.
To use the scanner, you need only connect it to e.g. your computer via Bluetooth
recognized there as an input device, e.g. like a keyboard. That means you can use the scanner
with any application you choose, as long as keyboard input is possible with that program.
To start using the bar code scanner, proceed as follows.
Charging the scanner:
• Before you use the scanner the first time, charge the rechargeable battery completely. This
takes about 4 to 5 hours.
• To do this, first open the rubber cover on the lower end of the scanner, at the point where you
can also attach the wrist loop. You can pull the cover out using just your fingernail.
• Next, connect the enclosed mini USB cable to the USB socket of the scanner.
• Now connect the USB cable to the USB port at which you want to charge the scanner. This
can be a USB port of a computer or even the port of a USB power supply.
• During charging, the LED of the scanner slowly flashes orange. As soon as the charging
process is finished, it lights up a steady orange.
When the battery is flat again, the orange LED begins to flash, and the scanner
beeps once. When the scanner then switches off, recharge the battery completely
before using the scanner again.
If the scanner is in energy-saving mode during charging, the LED does not flash or
light up.
Connecting the scanner to your device (Bluetooth
• First, turn on the bar code scanner. Press the middle, orange button briefly. If the scanner is
not in the normal stand-by mode, but in deep-sleep mode, you must hold down the button for
8 seconds. First the LED blinks quickly orange. Then the scanner beeps once. When the LED
briefly lights up a steady red, the scanner is active.
• Next, you have to select the profile that your device uses. An iPad, for example, uses the
"HID" profile, as does an Android smartphone from Samsung.
To select the "HID" profile, read the two codes A1 and A2 (for the "SPP" profile, read the
codes B1 and B2) from the English programming instructions. When you read the code A1,
the LED must first flash orange fast for a short time. Then the scanner beeps, and finally the
LED lights up a steady red for a short time.
If the LED does not flash orange fast for a moment, re-read the code A1. Only then should
you read the code A2. Here the LED first lights up a steady green; then the scanner beeps,
and finally the LED lights up a steady red again.
• Now activate Bluetooth
on the device on which you want to register the bar code scanner.
®
See the corresponding instructions for your device to find out details on how to proceed here.
• E.g. for Android, open the settings, switch to Connections and switch Bluetooth
the sliding switch. The search for devices occurs automatically. You may need to repeat the
search.
• The scanner is recognized e.g. as "R-A0E123". You may need to confirm the connection by
tapping on the name.
• As soon as it shows on your device as being coupled, the scanner is ready to use.
• To disconnect again, open the Options and select Uncouple. To do this on an Apple device,
you have to tap the Information button and ignore the device.
Should problems arise while you are establishing the connection, first reset the bar
code scanner to factory settings and try again.
interface. To find out which
®
. It is
®
):
®
on using
®
Quicklinks ausblenden:
Werbung
Inhaltsverzeichnis
