Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
Operation
• Place the device on a clean, horizontal, safe, stable and heat resistant surface.
• Check whether the on/off switch on the back of the device is off. The switch must be switched
to O.
• The soldering iron together with the soldering tip and the connection cable form one unit.
Connect the connection cable's round plug to the socket
iron station.
• Remove the plastic cover from the soldering tip and insert the soldering tip into the spiral
holder on the soldering iron station.
• Turn the control dial on the front of the device counter clockwise to the lowest power
level MIN.
• Connect the power plug to an appropriate power outlet.
• Turn on the soldering iron station by switching the on/off switch on the back of the device to I.
The power indicator POWER on the front of the device lights up red.
• Turn the control dial clockwise to the desired power level. At room temperature, the soldering
tip takes approx. 60 seconds to heat up to a temperature of approx. 260 °C.
• Begin the soldering job as soon as the device has heated up sufficiently. Do not operate the
device continuously at the highest power level. After a maximum of 15 minutes of continuous
operation at the highest power level, turn the control dial to the medium power level to
prevent the soldering tip from overstraining.
• During breaks or after completing a job, put down the soldering iron in the spiral holder on
the soldering iron station with the soldering tip facing downward. Turn the control dial to a low
power level during breaks.
• Turn the control dial counter clockwise to MIN after completing a job.
• Switch the on/off switch to O to turn off the device.
• Unplug the device and allow it to cool down sufficiently at a safe location.
Maintenance and cleaning
Only a specialist who is familiar with the risks and relevant regulations may carry out
repairs / open the housing.
Before starting to clean or maintain, the device must be disconnected from the
mains. Allow the device to cool down sufficiently.
a) General
• There are no components located inside the product you need to maintain. Never open/
dismantle the product.
• Do not use any aggressive cleaning agents, rubbing alcohol or other chemical solutions as
they can cause damage to the housing and malfunctioning.
• Do not use a file or sandpaper to clean the soldering tip. This may damage the soldering tip.
Use a slightly damp sponge to clean the soldering tip and remove soldering flux and soldering
wire residue. Dry the soldering tip thoroughly after cleaning.
• Clean the exterior of the device only with a soft, dry cloth or brush.
b) Replacing the soldering tip
• Before detaching/replacing the soldering tip turn the device off and unplug it from the power
outlet. Allow the soldering iron to cool down sufficiently.
• Replace the soldering tip if it is damaged or worn out.
If the soldering tip has loosened after a few hours of operation, remove it and
compress it lightly with a suitable tool on the opening for the heating element.
Disposal
Electronic devices are recyclable waste and must not be disposed of in the
household waste.
At the end of its service life, dispose of the product according to the relevant
statutory regulations.
You thus fulfil your statutory obligations and contribute to the protection of the environment.
Technical data
Power supply ........................................ 220 - 240 V/AC, 50 Hz
Power consumption .............................. 10 watts
Protection class .................................... II
Temperature range ............................... approx. 100 - 450 °C
on the front of the soldering
Operating temperature/humidity ........... -20 to +50 ºC, 15 – 95 % RH (non-condensing)
Storage temperature/humidity .............. -20 to +50 ºC, 15 – 95 % RH (non-condensing)
Dimensions (W x H x D) ....................... 72 x 58 x 93 mm (soldering iron station)
Weight .................................................. 0.615 kg
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or the capture in electronic data
processing systems require the prior written approval by the editor. Reprinting, also in part, is prohibited. This publication represent the
technical status at the time of printing.
© Copyright 2014 by Conrad Electronic SE.
V2_1114_02-HK
Werbung
Inhaltsverzeichnis
