Troubleshooting; Operating Elements; Operation - BASETech 2147832 Bedienungsanleitung

e) Work safety
• Ensure that there is sufficient lighting.
• Ensure proper ventilation during soldering. Solder and flux vapours can be harmful
to your health.
• Wash your hands thoroughly after working with solder. This is particularly
important when using lead-based solder.
• Do not put soldering alloys into your mouth. Do not eat or drink during soldering.
• Wear suitable protective clothing and safety goggles when soldering. Liquid/
splashing solder may cause serious burns or eye damage.

Operating elements

5 6 7 8
4
3
2
1
11
12
1 450 ºC preset button 7 Solder spools
2 300 ºC preset button 8 Power switch
I/O (ON/OFF)
3 200 ºC preset button
9 + button (increase
4 LCD display
working temp.)
5 Tip holders
10 - button (decrease
6 Spare tips
working temp.)
Setting up
a) Soldering iron tips
Risk of burns! Allow the tip to cool down before attempting to replace it. Do not
overtighten the tip.
• Pointed tip: Used for point soldering and thin
wires.
• Flat tip: Used for light electrical work.
• Store any unused tips in the tip holder (5).
b) Preparing the sponge
Place the sponge (16) into the tray (15) and moisten it slightly before use.

Operation

Always keep the tip tinned before switching off or storing for any period of time.
Do not keep the iron on for an extended period of time as this will break down the
surface of the tip.
• Connect the power plug (11) to a mains power outlet.
• Turn the power ON: Flip the power switch (8) to the [ I ] position.
The LCD display (4) shows the preset target temperature for a few seconds, followed by the
actual working temperature of the soldering tip (12).
• Select the required working temperature by:
- Pressing one of the preset buttons (1), (2), or (3).
- Pressing the temperature increase [+] (9) or decrease button [-] (10).
The temperature can be adjusted in 10 °C increments. The working temperature
range is 200 to 450 °C.
• Turn the power OFF: Flip the power switch to the [O] position.
• Disconnect the power plug (11) from the mains power outlet, and allow the soldering iron to
completely cool down before storing away.
9
14
10
13
16
11 Power plug
12 Soldering tip
13 Handle
14 Soldering iron holder
15 Tray for sponge
16 Sponge

Troubleshooting

Problem
Soldering iron does
not heat up.
Tip does not get hot
enough.
Maintenance and care
• Never clean the tip with coarse, abrasive materials like files.
• If oxide forms on the tip, lightly rub with abrasive paper, wipe clean, then immediately reheat
and re-tin the tip to prevent oxidation of the wettable surface.
• Do not use any aggressive cleaning agents, rubbing alcohol or other chemical solutions as
they can cause damage to the housing and malfunctioning.
Disposal
Electronic devices are recyclable waste and must not be disposed of in the
household waste. At the end of its service life, dispose of the product in accordance
with applicable regulatory guidelines.
You thus fulfill your statutory obligations and contribute to the protection of the
environment.
Technical data
15
Input voltage / current ................... 230 V/AC 50 Hz,
Power consumption ...................... 60 W
Temperature range ....................... 200 - 450 ºC
Temperature adjust ....................... 10 ºC increments
Solder ........................................... ø1 mm 10 g (lead-free flux core)
Protection class ............................ I
Operating conditions ..................... 0 to +45 ºC, 35 – 80 % RH (non-condensing)
Storage conditions ........................ 35 to +80 ºC, 35 – 80 % RH (non-condensing)
Dimensions ................................... Main unit: 125 x 95 x 150 mm (W x H x D)
Weight .......................................... 1.1 kg (net)
Visit the Conrad website and search Item No.: 2147832 for information about any
optional accessories, spares, or replacement parts.
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com). All rights
including translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or the capture in electronic data
processing systems require the prior written approval by the editor. Reprinting, also in part, is prohibited. This publication
represent the technical status at the time of printing.
Copyright 2020 by Conrad Electronic SE.
Suggestion
Check that the mains supply (socket) functions correctly. The
mains cable or power source may be faulty. Seek advice from an
electrician if needed.
• Let the tip cool down completely and check that it is screwed in
completely.
• The tip may be faulty, try using a different one.
ø1.5 mm 10 g (lead-free flux core)
Stand: 215 x 90 x 95 mm (W x H x D)
Soldering iron: ø36 x 260 mm
*2147832_v1_0420_02_dh_m_en