Specifications - Monacor PA-1120DM Bedienungsanleitung

6.2 Calling the announcements
1) Set the switch PLAY/REC (8) to PLAY.
2) Select the announcement by pressing one of the
buttons M 1 to M 6 (13). The display (5) shows the
corresponding memory location.
3) To replay the announcement, press the button
START/STOP (11). While replaying the announce-
ment, the indication EXEC (1) lights up.
4) Adjust the volume with the control LEVEL (14).
5) To finish the announcement before the end, press
button START/STOP (11) again. The indication
EXEC (1) extinguishes.
Note: An announcement can also directly be started by
pressing one of the buttons M 1 to M 6 (13). For this
refer to chapter 4 "Basic Settings" under item 4).
6.3 Repeat function
An announcement can also be repeated automatically
according to the settings carried out in chapter 4 under
item 2).
1) Set the switch PLAY/REC (8) to PLAY.
2) Select the announcement by pressing one of the
buttons M 1 to M 6 (13). The display (5) shows the
corresponding memory location.
3) For multiple replaying of an announcement press
the button REPEAT/STOP (12). While replaying the
announcement, the indication EXEC (1) lights up.
4) To finish the announcement before the end, press
the button REPEAT/STOP (12) again. The indica-
tion EXEC (1) extinguishes.
Note: An announcement with repeat can also directly
be started by pressing one of the buttons M 1 to M 6
(13). For this refer to chapter 4 "Basic Settings" under
item 4).
6.4 Deleting an announcement
1) Set the switch PLAY/REC (8) to REC.
2) Select the memory location of the announcement to
be deleted with one of the buttons M 1 to M 6 (13).
The display (5) shows the corresponding memory
location.
3) Activate the recessed button DEL (10) by means of
a small screw driver or similar tool. The an nounce -
ment is deleted.
6.5 Deleting all announcements
1) Switch the amplifier on and off again. The display
(5) shows the number "0".
2) Set the switch PLAY/REC (8) to REC.
3) Activate the recessed button DEL (10) by means of
a small screw driver or similar tool. The entire an -
nouncement memory is deleted.
All rights reserved by MONACOR
be reproduced in any form or by any means for any commercial use.
6.6 Headphones
The announcement can be checked with headphones
while recording or replaying.
1) Connect the headphones with the jack H.P. (3). If
2) Adjust the volume with the volume control LEVEL
Note: As long as the headphones are connected, the
announcement cannot be heard via the speakers
connected to the amplifier.
7 Remote-controlled Calling
1. If the insertion has been installed into an amplifier,
2. Via separate buttons for momentary action, the

8 Specifications

Input
Outputs
Frequency range
Sampling rate: . . . . . . . . . 16 kHz
Announcement memory: . 16 Mbit SRAM
Max. recording time: . . . . . 4 min 28 s
Max. memory holding time
w/o power supply: . . . . . . 60 days
Power supply: . . . . . . . . . . 17 V via amplifier or the
Dimensions, weight: . . . . . 194 × 40 × 125 mm, 420 g
Subject to technical modification.
® INTERNATIONAL GmbH & Co. KG. No part of this instruction manual may
required, use the supplied adapter.
(14).
of Announcements
to which the zone paging microphone PA-1120RC
or PA-6000RC can be connected, the announce-
ments may also be called by remote control via the
zone paging microphone.
remote-controlled calling of announcements is also
possible. For this connect the plug installed under
chapter 3, item 6), according to fig. 3.
M 2 M 3 M 4 M 5 M 6 M 1
REPEAT/ STOP
START/ STOP
Ž
Pin configuration
Mic: . . . . . . . . . . . . . . . -50 dB/600 Ω, unbal.
Line: . . . . . . . . . . . . . . . -10 dB/10 kΩ, unbal.
audio output: . . . . . . . . -10 dB, unbal., adjust able
headphones: . . . . . . . . 24 mW, ≥ 64 Ω
Mic: . . . . . . . . . . . . . . . 300 – 6400 Hz
Line: . . . . . . . . . . . . . . . 100 – 6400 Hz
to 0 dB with SEL 3
basic insertion unit
GB
9