Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
GB
Assignment of the DIP switches
Setting
Repeat
Time interval
Setting of the repeats
Number of
repeats
0
1
2
3
4
5
6
7
infinite
X = OFF
Setting of the time intervals
Time interval
1 s
2 s
4 s
8 s
32 s
1 min
4 min
8 min
not admissible
X = OFF
3) Set the output level with the jumper SEL 3:
pins 1 + 2:
no amplification of the output signal
pins 2 + 3:
amplification of the output signal by 10 dB
4) Select the mode for starting an announcement with
jumper SEL 4:
Jumper on Pin
1 + 2
2 + 3
3 + 4
setting ex factory
*according to the settings under item 2)
8
Memory location
M1
M2
M3
M4
SW 11 SW 12 SW 13 SW 14 SW 15 SW 16
SW 17 SW 18 SW 19 SW 20 SW 21 SW 22
Bit nummer
1
2
3
4
5
ON
X
X
X
X
X
ON
X
X
X
X
X
ON
X
X
X
X
X
ON
X
X
X
X
X
ON
X
X
X
X
X
ON
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
Bit nummer
1
2
3
4
5
ON
X
X
X
X
X
ON
X
X
X
X
X
ON
X
X
X
X
X
ON
X
X
X
X
X
ON
X
X
X
X
X
ON
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
Starting of an announcement
press one of the buttons M 1 to M 6 (13) =
single announcement
press one of the buttons M 1 to M 6 (13) =
repeated announcement*
at first press one of the buttons M 1 to M 6 (13)
and then button START/STOP (11) or
REPEAT/STOP (12)
5 First Setting into Operation
of the Insertion
When setting into operation for the first time, the com-
M5
M6
plete announcement memory is occupied with inter fer -
ing noise.
Important! Prior to the first operation delete in any
1) Switch on the amplifier. The number "0" appears on
the display (5).
2) Set the switch PLAY/REC (8) to REC.
6
7
8
3) Activate the button DEL (10) by means of a small
X
X
X
screw driver or similar tool. The entire announce-
X
X
X
ment memory is deleted.
X
X
X
X
X
X
6 Operation
X
X
X
X
X
6.1 Recording an announcement
X
ON
X
1) Set the switch PLAY/REC (8) to REC.
X
X
ON
2) Select the memory location by pressing one of the
X
X
X
buttons M 1 to M 6 (13). The display (5) shows the
corresponding memory location.
3) Set the switch MIC/LINE (4) according to the input
signal used:
for a microphone to position MIC,
for a unit with line level (e. g. cassette recorder,
6
7
8
CD player) to position LINE.
X
X
X
4) Connect the microphone or the unit to the jack
X
X
X
IN (6). If required, use the supplied adapter. If an
input signal is available, the LED SIG (9) lights up.
X
X
X
5) Adjust the recording volume with the control REC
X
X
X
LEVEL (2) so that the LED CLIP (7) just does not
X
X
X
light up.
X
X
6) Start the recording with the button START/STOP
X
ON
X
(11). While recording the LED EXEC (1) lights up.
X
X
ON
7) At the end of the recording stop the recording by
X
X
X
pressing the button START/STOP (11) again. The
LED EXEC (1) extinguishes.
8) Repeat the procedure for up to six announcements.
Notes
a The storage capacity of the entire announcement
memory is 4 minutes and 28 seconds. The capac ity
for each memory location is automatically adapted.
The recording stops automatically as soon as the
entire memory is filled up. It is poss ible to use the
entire memory e. g. even for only one announce-
ment lasting 4 minutes and 28 seconds.
b To replace an existing announcement by a new
one, the memory location must not be deleted
before. The previous announcement is automati-
cally overwritten.
c If the insertion is installed into the amplifier
PA-1120, PA-1240, PA-6240, PA-6480 or PA-6600, it
is possible to call an an nouncement of the memory
location M 6 automatically, e. g. via an alarm sensor
contact. In this case this memory location should be
reserved for a corresponding announcement.
case the memory contents:
Werbung
Inhaltsverzeichnis
