Delivery Content; Safety Instructions; Driver Installation - Renkforce 1013326 Bedienungsanleitung

Operating instructions
USB/eSATA Hard Disk Docking Station
Item no. 1013326
Intended use
The product is tended to be used for quickly connecting a SATA hard disk drive
(8.9cm/3.5" or 6.35cm/2.5" ) to a computer (via USB or eSATA), without installing it in
the enclosure. An external power supply unit is used to supply the power.
This product complies with the applicable National and European requirements. All
names of companies and products are the trademarks of the respective owner. All
rights reserved.

Delivery content

• Casing with integrated interface
converter
• USB cable
• eSATA cable
Features
• It is possible to install a SATA hard disk drive (8.9cm-/3.5" or 6.35cm-/2.5")
• Compatible with USB2.0 and USB1.1; USB2.0 is used for the high-speed transfer
mode; or, alternatively, it can be connected via eSATA.
• Power LED and LED for read/write access
• On/off switch
• Eject button

Safety instructions

The warranty will be void in the event of damage caused by failure to
observe these safety instructions. Liability for any and all consequential
damage is excluded!
We do not accept liability for damage to property or personal injury caused
by improper handling or non-compliance with the safety instructions! The
warranty will be void in such cases.
• The unauthorised conversion and/or modification of the product is
inadmissible because of safety and approval reasons (CE). Never
disassemble the product.
• The design of the mains transformer complies with protection class II.
Only use a standard mains socket as voltage source for the wall plug
transformer.
• Only use the external power adaptor supplied to power the device.
• The product must not get damp or wet as this may damage it, danger of a
fatal electric shock!
• The device is not a toy. Keep devices that operate on the mains voltage out
of the reach of children! Therefore, be especially careful when children
are around.
Only use the product out of the reach of children. They may try to insert
items into the docking station; this will damage the docking station!
• Do not leave packing materials unattended. They may become dangerous
playthings for children.
• Handle the product with care, it can be damaged by impacts, blows, or
accidental drops, even from a low height.

Driver Installation

The USB and also the eSATA drivers are integrated components in the operating
system, and your SATA controller, respectively.
Therefore, a data carrier does not accompany the delivery.
Connection via USB
Please note:
Either use the USB port or the eSATA port on the docking station. It is not
possi- ble to use both connections at the same time.
• Slot bracket with SATA/eSATA
adaptor cable
• Wall plug transformer
• Operating Instructions
• Switch off the docking station (switch position „O" = „OFF").
• Connect the low-voltage from the transformer supplied to the correct input on the
rear of the docking station's housing.
• Plug the wall plug transformer in to a mains socket.
• Connect the USB connector, on the rear, to a free USB2.0 port on your computer,
using the USB cable supplied.
• Naturally, a conventional USB1.1 port on the computer can be used instead of a
USB2.0 port. However, in this case the transfer data rate will be very low (USB1.1,
about 1MByte/sec max.).
• Before turning on the docking station, the SATA hard disk has to be inserted, see
section „Insertion of a Hard Disk".
Connection via eSATA
Please note:
Either use the USB port or the eSATA port on the docking station. It is not
possi- ble to use both connections at the same time.
• Switch off the docking station (switch position „O" = „OFF").
• Connect the low-voltage from the transformer supplied to the correct input on the
rear of the docking station's housing.
• Plug the wall plug transformer in to a mains socket.
• Connect the eSATA connector, on the rear, to a free eSATA port on your computer,
using the eSATA cable supplied.
If your computer does not have an eSATA port, you can use the slot bracket
provided, with eSATA port and SATA connection cable. This component has
to be installed in your computer.
If you do not have the appropriate knowledge ask a specialist to perform
the installation.
Exit the operating system and switch off your computer. Finally, disconnect
your computer/power supply from the mains!
Open the housing. Check if there is an unoccupied SATA connector on the
motherboard. For this consult the operating manual of the computer or the
motherboard.
Remove a slot bracket and screw the provide slot bracket with the eSATA
port firmly in to place. Connect the L-shaped SATA plug on the cable with a
free SATA connection on your motherboard.
Place all the cables so they cannot get into a fan, fix the cables e.g. with
cable fasteners.
Close the housing of the computer and reconnect it to the mains supply.
One of the SATA ports on your main board is now connected to the outside
of the computer via the cable and the eSATA connector.
• Before turning on the docking station, the SATA hard disk has to be inserted, see
section „Insertion of a Hard Disk".
Inserting a Hard Disk
• First, switch off the docking station (on/off switch on the back, switch
position „O" = „OFF").
• Insert a SATA hard disk vertically into the upper opening of the docking station,
so the terminal blocks on the SATA hard disk fit exactly on to the plugs inside the
enclosure (if you press the dust cover slightly with a finger, you can see the plugs
inside the enclosure).
Grasp the hard disk laterally on the housing, do not touch the plate with the
electronics. Electrostatic discharge can destroy the hard disk and the
docking station.
Do not use force when plugging in! However, the terminal blocks on the
SATA hard disk must lock into place.
• Now switch on the docking station!
Ejecting a hard disk
• Terminate all access to the hard disk drive that is inserted in the docking station.
Close all opened files.
• Switch off the docking station (on/off switch on the back, switch position „O" =
„OFF", power LED goes out).
• Wait at least 30 seconds, so that the magnetic disks can come to rest.
• Pressing the eject button causes a lever to lift up the hard disk mechanically and
unlocks the hard disk. This may be a bit stiff with 8.9cm/3.5" SATA hard disks. You
can also pull out the hard disks manually, without pressing the eject button.
The eject button is only for ejecting the hard disk, the button has no
electronic function.
Only grasp the hard disk laterally on the housing, do not touch the plate with
the electronics. Electrostatic discharge can destroy the hard disk and the
docking station.
Do not use force when extracting it!