Renkforce 1D ICR6307ABU Bedienungsanleitung Seite 4

• The standby mode.
Here, you can select between "Power-Saving mode OFF" and "ON". When "ON", the scanner
enters the standby mode after 1 minute of non-use. When "ON", it is on permanently.
• Prefix and suffix.
With this function, you can append either functions or characters to the scanned barcode. A
maximum of 5 prefixes or suffixes can be appended.
A function (prefix) would be, for example, if the "CTRL V" function is automatically performed
after the scan to append a text to the barcode from the clipboard.
A character (suffix) would be, for example, if the "+" character is appended automatically to
the barcode while scanning.
To configure, scan the "prefix" or "suffix" first and then the hexadecimal code from the table.
Prefix is the left side of the table. The codes start from "01" to "1F". Suffix is the right side of
the table. The codes start from "20" to "7E".
If you do not program all 5 memory locations, scan the "X" at the end.
Programming the different barcode languages
In the as-delivered condition, the scanner can just read barcodes, such as standard EAN code
"EAN-13". Please proceed as follows, to program other codes. You can find the programming
code in the "Barcode configuration method" chapter. The scanner must be in normal mode
while programming.
• First, read the "Start configuration" barcode using the scanner.
• Then, you read the code to enable or disable the desired barcode language. You must always
use "ENABLE" barcode to enable or "DISABLE" to disable which is in the same row as the
desired language barcode.
• Finally, scan the "End configuration" barcode as the last code to exit the programming mode.
If you want to enable or disable multiple barcode languages, it is enough if you read
the "Start configuration" barcode once at the beginning and the "End configuration"
bar code once at the end. In between, you can enable or disable any number of
barcode languages.
Reset configuration to defaults
• Scan the seven bar codes, which are below "Reset Configuration to Defaults" section in the
English programming instructions, following the sequence from 1 to 7.
• Then, the scanner is again reset to default values.
Care and cleaning
• Disconnect the product from the power supply before cleaning.
• The product requires no servicing on your part aside from occasional cleaning.
• Do not use any aggressive cleaning agents, rubbing alcohol or other chemical solutions as
they can cause damage to the housing and malfunctioning.
• Clean the product with a dry, fiber-free cloth.
• Clean the product very carefully; otherwise you may scratch it.
• Do not press too heavily on the glass cover, as this can lead to breakage.
• Do not immerse the product in water.
Declaration of conformity (DOC)
Conrad Electronic SE, Klaus-Conrad-Straße 1, D-92240 Hirschau hereby declares that this
product conforms to the 2014/53/EU directive.
Click on the following link to read the full text of the EU declaration of conformity:
www.conrad.com/downloads
Select a language by clicking on a flag symbol and enter the product order number
in the search box. You can then download the EU declaration of conformity in PDF
format.
Disposal
Electronic devices are recyclable waste and must not be disposed of in the
household waste. At the end of its service life, dispose of the product according to
the relevant statutory regulations.
You thus fulfil your statutory obligations and contribute to the protection of the
environment.
Technical data
Operating voltage ......................................5 V/DC
Power supply .............................................via USB
Power consumption during operation ........max. 250 mA
Power consumption while charging ...........max. 500 mA
Charging time ............................................4 – 5 hours
Rechargeable battery ................................ 1 Li-ion rechargeable battery, 3.7 V/DC 800 mAh,
Scanner type .............................................1D, CCD engine
Transmission frequency.............................2.4 Ghz
Frequency band .........................................ISM Band for 2.4GHz (2400~2483.5MHz)
Transmit power ..........................................max. up to +12dBm
Range ........................................................max. 100 m, in open space
Scanning rate ............................................max. 300 scans per second
Operating temperature ..............................0 to +50 °C
Storage temperature ..................................-10 to +60 °C
Air humidity ................................................5 – 95 % relative air humidity
Supported barcodes .................................. EAN-13, EAN-8, UPC-A, UPC-E, ISSN, ISBN,
Supported Operating Systems .................. Windows
Length of the USB cable ............................approx. 140 cm
Dimensions (W x H x D) ............................approx. 60 x 165 x 90 mm (barcode scanner)
Weight .......................................................approx. 165 g (barcode scanner)
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or the
capture in electronic data processing systems require the prior written approval by the editor. Reprinting, also in
part, is prohibited. This publication represent the technical status at the time of printing.
Copyright 2018 by Conrad Electronic SE.
non-removable
Codabar, Code 128, Code 93, ITF-6, ITF-14,
Interleaved 2 of 5, Industrial 2 of 5, Matrix 2 of 5,
GS1 Databar, Code 39, Code 11, MSI-Plessey,
Plessey
XP (only 32 bit), Windows Vista™,
®
Windows 7, Windows 8 (32 and 64 bit);
® ®
MacOS 9, MacOS X
approx. 225 g (charging station)
*1277852_V3_0318_02_mxs_m_en