Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
Operating instructions
2.5 SATA HDD hard drive casing
Item no. 1277640
Intended use
This product is intended for mounting a 6.35 cm / 2.5" SATA hard drive or SATA SSD
(not included) of 5 mm, 7 mm or 9.5 mm in height and for operation via a USB 3.0 port.
Power is supplied via a USB 3.0 port.
For safety and approval purposes (CE), you must not rebuild and/or modify this product.
If you use the product for purposes other than those described above, the product may
be damaged. In addition, improper use can cause hazards such as short circuiting,
fire, electric shock etc. Read the instructions carefully and keep them. Make this
product available to third parties only together with its operating instructions.
This product complies with the statutory national and European requirements. All
company names and product names are trademarks of their respective owners. All
rights reserved.
Delivery content
• Hard drive casing
• USB 3.0 cable (approx. 60 cm in length)
• 5 x Small screw
• 2 x Rubber support (45 x 10 x 3 mm for 7 mm HDD)
• 2 x Rubber support (45 x 10 x 5 mm for 5 mm HDD)
• Phillips screwdriver
• Storage bag
• Operating instructions
Safety instructions
Read the operating instructions carefully and especially observe the safety
information. If you do not follow the safety instructions and information on
proper handling in this manual, we assume no liability for any resulting
personal injury or damage to property. Such cases will invalidate the
warranty/guarantee.
• The device is not a toy. Keep it out of the reach of children and pets.
• Do not leave packaging material lying around carelessly. These may
become dangerous playing material for children.
• Protect the product from extreme temperatures, direct sunlight, strong
jolts, high humidity, moisture, flammable gases, vapours and solvents.
• It is intended for indoor use only. Do not use it outdoors. Contact with
moisture, e.g. in bathrooms, must be avoided under all circumstances.
• Do not place the product under any mechanical stress.
• If it is no longer possible to operate the product safely, take it out of
operation and protect it from any accidental use. Safe operation can no
longer be guaranteed if the product:
- is visibly damaged,
- is no longer working properly,
- has been stored for extended periods in poor ambient conditions or
- has been subjected to any serious transport-related stresses.
• Please handle the product carefully. Jolts, impacts or a fall even from a
low height can damage the product.
• Avoid locations with strong magnetic fields, such as near machines or
speakers.
• Also observe the safety and operating instructions of any other devices
which are connected to the product.
• Never use the product immediately after it has been brought from a cold
room into a warm one. The condensation generated could destroy the
product.
• Allow the device to reach room temperature before connecting and using
it. This may take several hours.
• Make sure that the cable is not bent or crushed when setting up the
product.
• Consult an expert when in doubt about operation, safety or connection of
the device.
• Maintenance, modifications and repairs are to be performed exclusively
by an expert or at a qualified shop.
• If you have questions which remain unanswered by these operating
instructions, contact our technical support service or other technical
personnel.
Operating elements
1 Casing cover
2 USB 3.0 port
3 Blue LED (power supply)
4 Red LED (data transfer)
5 Casing bottom
Mounting the hard drive/SSD
1. If the hard drive casing is screwed down at
the time of delivery, remove the two screws
on the side. Then pull down the casing
cover (1) in order to open the casing.
2. Connect a 6.35 cm / 2.5" SATA hard drive
to the SATA connector on the casing
bottom (5).
3. For hard drives/SSD of 5 or 7 mm in height,
attach an appropriate rubber strip each to
the front and rear area of the casing cover.
The rubber strip secures the hard drive
inside the casing to prevent the hard drive
from slipping off the terminal block. Close
the housing.
4. Secure the casing with 2 screws, using the
Phillips screwdriver provided.
1 2
3 4
5
Werbung
Inhaltsverzeichnis
