Hameg Instruments LCR-Bridge HM8118 Handbuch Seite 31

Deutsch
English
General remarks regarding the CE marking
Programmable LCR-Bridge HM8118
Specifications
1 Important hints
1.1 Symbols
1.2 Unpacking
1.3 Positioning
1.4 Transport and storage
1.5 Safety instructions
1.6 Proper operating conditions
1.7 Warranty and Repair
1.8 Maintenance
1.9 Line fuse
1.10 Power switch
2 Controls and display
3 Quick Introduction
3.1 Hardware supplied
3.2 Measurement of a capacitor
3.3 Measurement of an inductor
3.4 Measurement of a resistor
4 First-time operation
4.1 Connecting the instrument
4.2 Turning on the instrument
4.3 Line frequency
4.4 Measuring principle
4.5 Main measurement and second measurement value
display
4.6 Display of measurement results
4.7 Choosing of the measurement range
4.7.1 Automatic range selection
4.7.2 Manual range selection
4.8 Switching the equivalent measurement
circuitry
5 Setting of instrument parameters
5.1 Menu function SETUP
5.1.1 Frequency FRQ
5.1.2 Voltage LEV
5.1.4 Measuring range RNG
5.1.5 Measuring speed SPD
5.1.6 Triggering TRIG
5.1.7 DELAY
5.1.8 Average (AVG)
5.1.9 Display of test signal levels
V (voltage) / I (current)
m m
5.1.10 Guarding GUARD
5.1.11 Deviation DEV_M
5.1.12 Reference REF_M
5.1.13 Deviation DEV_S
5.1.14 Reference REF_S
5.1.15 Constant voltage CST V
5.2 Menu function CORR
5.2.1 Calibration OPEN
5.2.2 Calibration SHORT
5.2.3 Calibration LOAD
5.2.4 NUM
3 5.2.5 Frequency FRQ
5.2.6 Function FUNC
5.2.7 Reference value LOADM for the main
measurement value
5.2.8 Reference value LOADS for the second
measurement value
30
5.3 Menu function SYST
32 5.3.1 CONTRAST
5.3.2 KEY BEEP
33 5.3.3 TALK ONLY
5.3.4 Baud rate BAUDS
34
5.3.5 MAINS FRQ
34 5.3.6 Instrument information INFO
34
34 5.4 Storing / Recalling of instrument settings
34 and parameters
34 5.5 Factory settings
34
35 6 Calibration
35 6.1 Open circuit calibration procedure
35 6.2 Short circuit calibration procedure
35 6.3 Procedure of the calibration with a known load
36 7 Connecting of components and
7.1 4 wire measuring adapter HZ181
38 7.1.1 Specifications
38 7.1.2 Calibration
38
38 7.2 Kelvin measurement cable HZ184
39 7.2.1 Specifications
7.2.2 Calibration
39
39 7.3 4 wire transformer measurement cable HZ186
40 7.3.1 Specifications
40 7.3.2 Calibration
40
7.4 4 wire SMD test adapter HZ188
40 7.4.1 Specifications
41 7.4.2 Calibration
41
41 7.5 Option HO118 binning interface for
41 component sorting
42 7.5.1 Specification
42 7.5.2 Container (BIN) setup
7.5.3 Examples
43
43 8 Remote Control
8.1 Dual Interface HO820 (USB/RS-232)
43
43 8.2 IEEE-488 (GPIB) interface HO880
44 8.3 Communication
44
9 Command reference
44
44 9.1 Setup Commands
44 9.2 Control Commands
9.3 Commands for the request of results
44 9.4 Binning Commands
9.5 Setup and Control Commands
44
44
44
44
44
45
45
45
45
45
45
C o n t e n t
Subject to change without notice
45
45
45
45
46
46
46
46
46
46
46
46
46
47
47
47
47
48
48
48
48
49
49
49
49
50
50
50
50
50
51
51
52
52
53
53
53
53
54
54
55
55
55
56
31