Technical Data; Unpacking - Scheppach MIX125 Anleitung

AC Motor
AC motor 230 V/ 50 Hz, mains voltage 230 Volt
/ 50 Hz.
Use of a residual current protection device ("FI")
is recommended for a 230V connection. If you
use an extension cable, insert it directly into the
FI.
If operating it in Switzerland, insert the concrete
mixer only in sockets that are protected by a re-
sidual current-operated circuit breaker.
1. Supporting stand, front
2. Motor casing
3. Frame
4. Swivel wheel
5. Drum upper section
Motor
Capacity
Protection class
Dimensions
Weight
Sound pressure level L / uncertainty K
pA
Sound power level L / uncertainty K
WA
Warning: Noise can seriously damage your
D GB
health. If the engine noise exceeds 85 dB (A),
please wear appropriate hearing protection. If
the electrical connection is faulty, the current
may drop when the machine starts. This may af-
fect other machines (e.g. flashing lights). If the
electric output corresponds to Zmax <0.27, such
interference should not occur. (If it does, notify
your dealer).
Take the concrete mixer out of the carton with the
help of two persons.
Caution!
The concrete mixer should be used only after it
is installed fully.
1. Installing wheels Fig.3
Install splint on both sides, washer, wheel (12),
washer, splint on the supporting stand rear with
wheel axle (11).
Bend the splints slightly after installation
2. Installing the front supporting stand with
frame Fig.4
Install front supporting stand (1) with 2 M8x70
screws, 2 8mm washers, 2 lockwashers, 2 M8
nuts on the frame (3) and tighten the screws.
Mains connection and extension cable can have
3 wires as well as 2.
3-wire: P + N + SL. - (1/N/PE); 2-wire: P + N –
(1/N)
Extension cables must have a minimum cross-
section of 1.5 mm².
Connecting cable, plug and coupling jack must
be protected against water spray.
The mains connection is protected with a maxi-
mum 16A fuse.
Equipment packing list Fig.1
6. Bearing bracket
7. Drum lower section
8. Instructions
9. Mixer
10. Bag provided (Fig. 2 Content)

Technical data

MIX125
230V / 50 Hz 0,55 kW
125 l
IP45D
1200mm x 710mm x 1400mm
48 kg
67dB(A) / 9.8dB(A)
97dB(A) / 9.8dB(A)
Information on noise
•
The vibration emission value given below has
been measured by a standardized test, and
can be used for comparing one power tool to
another;
•
The vibration emission value given below may
also be used for a first assessment of exposure.
Warning:
• The vibration emission value may vary during
actual use of the power tool from the specified
value, depending on the manner in which the
power tool is used;

Unpacking

Check to ensure that the delivery is complete.
Inform the dealer if there are faults.
Montage
3. Installing the frame with the wheel sup-
ports Fig. 5
Install frame and wheel supports fully with 2
M8x70 hexagon bolts, 2 8mm washers, 2 lock-
washers and 2 M8 nuts. Tighten the screws.
4. Installing the lower section of drum with
frame Fig.6
Set the lower section of the drum (7) with bear-
ing bracket (6) on the pre-installed framework,
tighten with 2 M8x65 hexagon bolts, 2 washers,
2 lockwashers and 2 M8 nuts.
Secure with a Ø42 spiral ring.
5. Installing mixer Fig.7
Lock mixer (9) with 2 M8x20 cross-head screws
to the lower section of the drum with 2 washers,
16
Connections and repairs of the electrical
equipment should be performed by electri-
cians only.
Please quote the following information in
your queries:
• Current type of the motor.
•
Data on the machine ratings plate.
When returning the motor, always send the com-
plete drive unit with switch.
11. Supporting stand, rear with wheel axle
12. 2 wheels
13. Locking washer
MIX140
230V / 50Hz 0,55 kW
140 l
IP45D
1200mm x 710mm x 1400mm
49,5 kg
67dB(A) / 4.4dB(A)
91dB(A) / 4.4dB(A)
•
Try to keep exposure to vibration to a mini-
mum. Examples of ways to reduce vibration
levels are wearing gloves when using the
tool and limiting working hours. In doing so,
all parts of the operating cycle must be taken
into account (for example, times in which the
power tool is turned off, or when it is turned
on without load).
2 lockwashers and 2 M8 nuts. Insert one rubber
washer each between mixer and drum.
6. Installing upper section of drum Fig.8
Place rubber ring on the lower section. Place the
upper section of drum on it.
Caution! The pasted arrows mark the exact direc-
tion of the upper or lower section of the drum.
Align the upper section of the drum and install
it on the lower section with 6 M8x16 cross-head
screws with washers and tighten. Lock mixer (9)
with 2 M8x20 cross-head screws and 2 lock-
washers to the lower section of the drum with 2
washers, 2 lockwashers and 2 M8 nuts. Insert
one rubber washer each between mixer and
drum.