Nordpeis N-36V Montageanleitung Seite 13

Remember that the insert must always be cold when
inspected.
Ashes
The ashes should be removed with regular intervals.
Be aware that the ashes can contain hot ember even
several days after the fire is finished. Use a container
of non-combustible material to remove the ashes. It is
recommended to leave a layer of ashes in the bottom
as this further insulates the burn chamber. Take
care with the insulation plates when the ashes are
removed, particularly when using an ash spade.
Thermotte®/Vermiculite Plates
These insulating plates in the burn chamber (FIG 7)
contribute to a high combustion temperature, which
leads to cleaner combustion of the wood and a higher
rate of efficiency. Any fissures in the plates will not
reduce their insulation efficiency.
If new plates are needed, contact your dealer. Please
note: Wood logs that are too long can cause additional
strain and crack the plates, due to the tension created
between the side plates.
In case it is necessary to take out the insulation
plates, this is done in following order.
A. Front border
B. Right side plate
C. Left side plate
D. Back plate
E. Bottom plate
F.
Smoke baffle (steel)
G. Two inner ceiling plates
Door and Glass
Should there be any soot on the glass it may be
necessary to clean it. Use dedicated glass cleaner.
(NB! Be careful, detergents can damage the varnish).
If different detergents are used they may damage the
glass. A good advice for cleaning the glass is to use a
damp cloth or kitchen roll paper and apply some soot
from the burn chamber. Rub around the soot on the
glass and finish off with a piece of clean and damp
kitchen roll paper. NB! Only clean when the glass is
cold.
Check regularly that the transition between the glass
and the door is completely tight. Possibly tighten the
screws that hold the glass in place - but not too hard,
as this can cause the glass to crack. Periodically,
it may be necessary to change the gaskets on the
door to ensure that the burn chamber is air tight and
working optimally. These gaskets can be bought as a
set including ceramic glue.
In order to unhinge the door, do as follows:
Remove the transportation safety device (FIG 8A) that
is fastened in the upper door hinge, in case it is still in
place. Open the door and tighten carefully the little
Allen screw (B) that is on the inside of the door, just
above the lower hinge. Hold the door and carefully
press the top of the door towards the top of the door
frame simultaneously as the lower part is pulled
away from the door frame. Lower the door until the
upper hinge releases from the door frame (FIG 8B).
Remember to loosen the Allen screw again when the
door is put back on. This will release the inner bolt in
the hinge so that this will fall in place.
REFRACTORY
GLASS CANNOT
BE RECYCLED
Refractory glass should
be disposed of as resid-
ual waste, together with
pottery and porcelain
Recycling of the refractory glass
Refractory glass cannot be recycled. Old glass, bre-
akage or otherwise unusable refractory glass, must be
discarded as residual waste. Refractory glass has a
higher melting temperature, and can therefore not be
recycled together with glass. In case it would be mixed
with ordinary glass, it would damage the raw material
and could, in worst case end the recycling of glass.
It is an important contribution to the environment to
ensure that refractory glass does not end up with the
recycling of ordinary glass.
7. Warranty
Read the entire user manual carefully to ensure
proper use and installation of your new Nordpeis
insert. After installation the insert should be
checked.
The steel inserts from Nordpeis AS benefit of a
5-year warranty. The warranty requires the insert to
be installed in accordance with applicable laws and
regulations, as well as the user manual. Notification
of damage and possible consignment of parts for
replacement must be done immediately to the retailer
where the insert was bought. Any claim must be
submitted with a dated invoice or a valid warranty
card.
The warranty does not include consumables such
as: Thermotte®/Vermiculite plates, smoke baffle,
glass and gaskets. Should any of the mentioned parts
break, or need to be changed due to wear and tear,
new parts can be ordered from your retailer. However,
if a material or production error can be documented
on any of the mentioned parts, the warranty is valid for
2 years after the date of purchase.
The warranty does not include damages that are
caused by wrong installation or misuse of the insert,
e.g. incorrect draught regulation or use of incorrect
GB 13