Technical Data; Before Starting The Equipment - EINHELL TE-CI 18 Li Originalbetriebsanleitung

4. Technical data

Motor power supply: ............................... 18 V DC
Idling speed: .....................................0-2300 min
Blow rate: .........................................0-2900 min
Clockwise/counter-clockwise: ........................Yes
Bit mount: ................................... 1/4 " (6.35 mm)
Battery charger output voltage: .............. 21 V DC
Battery charger output current: ....................... 3 A
Charging unit supply
voltage: .............................. 200-260V~ 50-60Hz
Battery type: ...................................... Lithium-ion
Number of battery cells: .............................. 5/10
Battery capacitance: ........................... 1.5/3.0 Ah
Weight: .......................................................1.4 kg
Max. screw diameter: ................................. 8 mm
Danger!
Sound and vibration
Sound and vibration values were measured in
accordance with EN 60745.
L sound pressure level ........................ 86 dB(A)
pA
K uncertainty ............................................. 3 dB
pA
L sound power level .......................... 97 dB(A)
WA
K uncertainty ............................................. 3 dB
WA
Wear ear-muff s.
The impact of noise can cause damage to hea-
ring.
Total vibration values (vector sum of three direc-
tions) determined in accordance with EN 60745.
Screwing without hammer action
Vibration emission value a
K uncertainty = 1.5 m/s
The specifi ed vibration value was established in
accordance with a standardized testing method. It
may change according to how the electric equip-
ment is used and may exceed the specifi ed value
in exceptional circumstances.
The specifi ed vibration value can be used to
compare the equipment with other electric power
tools.
The specifi ed vibration value can be used for initi-
al assessment of a harmful eff ect.
Anl_TE_CI_18_Li_Kit_SPK7.indb 18 Anl_TE_CI_18_Li_Kit_SPK7.indb 18
-1
-1
= 12.8 m/s
2
h
2
- 18 -
GB
Keep the noise emissions and vibrations to a
minimum.
•
Only use appliances which are in perfect wor-
king order.
•
Service and clean the appliance regularly.
•
Adapt your working style to suit the appliance.
•
Do not overload the appliance.
•
Have the appliance serviced whenever ne-
cessary.
•
Switch the appliance off when it is not in use.
•
Wear protective gloves.
Caution!
Residual risks
Even if you use this electric power tool in
accordance with instructions, certain resi-
dual risks cannot be rules out. The following
hazards may arise in connection with the
equipment's construction and layout:
1. Lung damage if no suitable protective dust
mask is used.
2. Damage to hearing if no suitable ear protec-
tion is used.
3. Health damage caused by hand-arm vib-
rations if the equipment is used over a pro-
longed period or is not properly guided and
maintained.
Limit the operating time.
All stages of the operating cycle must be conside-
red (for example, times in which the electric tools
are switched off and times in which the tool is
switched on but operates without load).
Caution!
The metal gear head may become hot during pro-
longed operation.

5. Before starting the equipment

Be sure to read the following information before
you put the cordless screwdriver into operation:
1. Charge the battery pack with the charger sup-
plied. An empty battery pack requires a char-
ging period of approximately 0.5 to 1 hour.
2. Only ever use screwdriver bits which are
suitable for the purpose and in faultless con-
dition.
3. Before you begin to screw in walls and ma-
sonry, check for concealed electric wiring,
gas pipes and water pipes.
03.11.14 08:44 03.11.14 08:44