Werbung
Verfügbare Sprachen
Verfügbare Sprachen
Please, also see the insert «Cell
disposal at the end of the useful life
of the appliance».
Wall fastening
Fasten wall plugs and screws in the
wall. However, turn screws into wall
plugs only so far that screw heads
can be stuck into the two openings
2
in the back of the charging unit
1
1
. By pulling the charging unit
down, the screws will be fastened in
the two slits over the screw
2
openings
.
You have to pull out only as much
cord from the cord storage as you
need to the mains plug.
Connecting
1
The charging unit
can be
connected to any voltage outlet –
even to shaver sockets – between
220 - 240 volts ac (~) without
8
converting. Place the power unit
,
facing the front, on the charging
j
base
.
6
The green charge indicator
will
light up at 220 - 240 volts, whenever
the power unit is inserted and
recharging on the plugged-in
charging unit. The power unit may
warm up somewhat. This has no
significance on the unit's operation.
Over-charging is impossible. To
maintain your plaque remover's full
power capacity, the power unit
should always be stored in the
plugged-in charging unit after use.
8
Important: The power unit
switches off automatically when
1
placed in the carging unit
to
permit recharging. Make sure that
there is electrical power in the
4
socket when you recharge your
power unit. Sockets in mirror
cabinets over wash basins or
shaver sockets in bathrooms may
be without electrical power when
the light is turned off.
Switch
8
The power unit
is switched on
and off by pressing the circular
7
marking on the blue switch
(b).
When placed in the charging unit,
the power unit is automatically
switched off. The blue switch is
waterproof and can be cleaned
under running water.
Preserving the rechargeable
batteries
To maximize the capacity and life of
the rechargeable batteries, they
should be fully charged (for 16
hours on 220 - 240 volts) before the
first use and then fully discharged
by using. Then recharge to full
capacity again. This discharging/
charging procedure should be done
every six months.
Use
After the power unit has been fully
charged, attach one of the brush-
4
head
to the power unit (a). Before
doing so, you may fix one of the
3
coloured rings
onto the end of the
brushhead. The brushhead must
face the same direction as the
7
9
switch
. The roll-stop
prevents
8
the power unit
from rolling off a
flat surface.
Before brushing your theeth, rinse
your mouse thoroughly and wet the
brushhead. You may use regular
toothpaste. To avoid splashing,
switch the power unit on after
guiding the brushhead to your teeth.
Then, move the brushhead along
the chewing surfaces of your teeth.
After that, hold the brushhead at a
90° angle and guide it along the
outsides and then the insides of
your teeth. Be sure to get into the
spaces between your teeth as well
as along the gumline. The Braun
Oral-B Plak Remover will auto-
matically provide the right cleaning
action. You do not need to press
hard. To thoroughly remove plaque,
brush for at least 2 minutes.
After cleaning your teeth, rinse your
mouth thoroughly again. During the
first few days of using the Braun
Oral-B Plaque Remover, your gums
may bleed slightly, particularly if
they normally tend to do so. After a
few days, the bleeding will ge-
nerally stop. If your gums continue
to bleed after 2 weeks, you should
see your dentist.
The brushes have soft, end-
rounded bristles in order to protect
your gums. Clinical tests have
shown that the best cleaning effect
is achieved by gently moving the
brush from tooth to tooth, without
exerting pressure. A change in the
shape of the brush is normal after
use. This is influenced by your
individual cleaning technique, but
does not affect the efficiency of th
brush.
INDICATOR brushheads
The INDIDCATOR brushhead (e / l)
helps you monitor your brushing
performance.
Dentists recommend that you
replace any toothbrush every 3 to 4
months, since worn bristles do not
clean plaque away as effectively as
new ones. With proper brushing,
twice a day for two minutes, the
green colour will wear half-way
down the bristles in this 3 to 4 month
period, provided you use toothpaste
(e / II).
If the bristles begin to splay before
the green colour starts to recede it
means that you are exerting too
much pressure on your teeth and
gums, and wearing out the brush-
head too quickly (e / III).
The INDICATOR brushhead helps
to improve your brushing per-
formance, thus optimizing excep-
tional plaque removal and the life of
the brushhead.
Replacement brushheads are
available at your dealer or Braun
Service Centres.
Cleaning
To maintain the function of the
4
brushhead
rinse thoroughly for
several seconds with the power unit
8
switched on under running water
(not warmer than 80 °C) after use
(c).
Clean the brushheads and the
power unit by simply holding them
under running water (d). Wipe the
power unit dry. After cleaning place
8
the power unit
back on the
j
charging base
. The green charge
6
indicator
will light up at 220 - 240
volts.
5
Werbung
