Dust/Chip Extraction - Bosch PKS 16 Multi Bedienungsanleitung

20 | English
Selecting a Saw Blade
An overview of recommended saw blades can be found at the
end of this manual.
Removal of the Saw Blade (see figure A)
– To avoid damage, provide for sufficient clearance between
power tool and workpiece.
– Hold the power tool by the handle 11.
– Press release lever 4 for base plate 3 down. The base plate
3 opens.
– Press the spindle lock button 12 and keep it pressed.
 The spindle lock button 12 may be actuated only when
the saw spindle is at a standstill. Otherwise, the power
tool can be damaged.
– Using Allen key 16, unscrew the clamping bolt with clamp-
ing flange 15 by turning in rotation direction .
– Remove the saw blade 14 and mounting flange 13 from the
saw spindle.
Mounting the Saw Blade (see figure A)
– To avoid damage, provide for sufficient clearance between
power tool and workpiece.
– Hold the power tool by the handle 11.
– Press release lever 4 for base plate 3 down. The base plate
3 opens.
– Clean the saw blade 14 and all clamping parts to be assem-
bled.
– Insert the mounting flange 13.
– Mount the saw blade 14 to mounting flange 13. The cutting
direction of the teeth (arrow direction on the saw blade)
and the direction-of-rotation arrow on the saw must corre-
spond.
– Press the spindle lock button 12 and keep it pressed.
– Using Allen key 16, screw in the clamping bolt with clamp-
ing flange 15 by turning in rotation direction . The tight-
ening torque is 6–9 Nm, which corresponds with hand-
tight plus ¼ turn.
– Close the base plate 3 again. It can be heard to engage.
Mounting/Replacing the Diamond Cutting Disc
(for Cutting Applications, e. g. Cutting Tiles)
 Before any work on the machine itself, pull the mains
plug.
 When mounting and replacing diamond cutting discs, it
is recommended to wear protective gloves.
 Diamond cutting discs become very hot during opera-
tion; do not touch them until they have cooled down.
 Use only diamond-tipped cutting discs.
Do not used segmented cutting discs and do not use
bonded, reinforced cutting discs.
 Release and close the base plate 3 carefully, in order to
avoid injury and material damage.
Selecting a Diamond Cutting Disc
An overview of recommended diamond cutting discs can be
found at the end of these instructions.
Removing the Diamond Cutting Disc (see figure A)
– To avoid damage, provide for sufficient clearance between
power tool and workpiece.
1 609 92A 0GB | (11.9.13)
– Hold the power tool by the handle 11.
– Press release lever 4 for base plate 3 down. The base plate
3 opens.
– Press the spindle lock button 12 and keep it pressed.
 Actuate the spindle lock button only when the grinder
spindle is at a standstill. Otherwise, the machine may be-
come damaged.
– Using Allen key 16, unscrew the clamping bolt with clamp-
ing flange 15 by turning in rotation direction .
– Remove the diamond cutting disc 21 and the mounting
flange 13 from the saw spindle.
Mounting the Diamond Cutting Disc (see figure A)
– To avoid damage, provide for sufficient clearance between
power tool and workpiece.
– Hold the power tool by the handle 11.
– Press release lever 4 for base plate 3 down. The base plate
3 opens.
– Clean the diamond cutting disc 21 and all clamping parts
to be mounted.
– Insert the mounting flange 13.
– Mount the diamond cutting disc 21 to mounting flange 13.
The direction arrow on the diamond cutting disc and the di-
rection-of-rotation arrow on the power tool must corre-
spond.
– Press the spindle lock button 12 and keep it pressed.
– Using Allen key 16, screw in the clamping bolt with clamp-
ing flange 15 by turning in rotation direction . The tight-
ening torque is 6–9 Nm, which corresponds with hand-
tight plus ¼ turn.
– Close the base plate 3 again. It can be heard to engage.

Dust/Chip Extraction

 Before any work on the machine itself, pull the mains
plug.
 Dusts from materials such as lead-containing coatings,
some wood types, minerals and metal can be harmful to
one's health. Touching or breathing-in the dusts can cause
allergic reactions and/or lead to respiratory infections of
the user or bystanders.
Certain dusts, such as oak or beech dust, are considered
as carcinogenic, especially in connection with wood-treat-
ment additives (chromate, wood preservative). Materials
containing asbestos may only be worked by specialists.
– Use a dust extraction system suitable for the material
being worked.
– Provide for good ventilation of the working place.
– It is recommended to wear a P2 filter-class respirator.
Observe the relevant regulations in your country for the
materials to be worked.
 Prevent dust accumulation at the workplace. Dusts can
easily ignite.
External Dust Extraction (see figure E)
Insert the extraction adapter 9 into sawdust ejector 20 and
turn the extraction adapter 9 in the direction of the arrow until
it can be felt to engage.
Insert a vacuum hose 17 (accessory) into the extraction
adapter 9. Connect the vacuum hose 17 with a vacuum
Bosch Power Tools