Cameo NANOSPOT 120 Bedienungsanleitung Seite 14

OPERATION / BEDIENUNG / UTILISATION / OPERACIÓN / OBSŁUGA / UTILIZZO
EN
OPERATION
When the spotlight is properly connected to the mains, the motors are reset (Display = "InIt"). Within a few seconds, the spotlight is ready for use
and changes to the mode that was previously selected.
SELECTING THE DMX STARTING ADDRESS AND DMX MODE
Press the MODE button repeatedly until "dMX", "PrEF", "SLAV", "Soun", or "Auto" appears on the display. Now use the UP and DOWN buttons to
select the "dMX" menu item and confirm by pressing ENTER. "Add" now appears on the display and by pressing ENTER once more, you can select
the DMX start address as desired using the UP and DOWN buttons (A001 - A508). After confirming with ENTER, "SAVE" is briefly displayed on the
display. To set the DMX operating mode, select the menu item "dMX", press ENTER and then use the UP and DOWN buttons to select the menu item
"ChAn". Press ENTER and use the UP and DOWN buttons to select the desired DMX mode (5Ch, 9Ch, 11Ch). After confirming with ENTER, "SAVE" is
briefly displayed on the display. The synchronous control of multiple spotlights (same model) through a DMX control unit (e.g. DMX console) can be
achieved by assigning the spotlights to an identical DMX start address and DMX mode and connecting them using DMX cables.
-> ENTER ->
<- MODE
-> ENTER ->
<- MODE
AUTOMATIC CONTROL MODE (AUTO)
Select one of the 7 different Auto programs (Sh01 - Sh07) and their speed (SP00 - SP99). Press the MODE button repeatedly until "dMX", "PrEF",
"SLAV", "Soun", or "Auto" appears on the display. Now use the UP and DOWN buttons to select the "Auto" menu item and confirm by pressing
ENTER ("SAVE" is briefly displayed on the display). Press twice on ENTER, then use the UP and DOWN buttons to select one of the 7 Auto programs
(the last 2 digits of the display will flash). After confirming with ENTER, "SAVE" is briefly displayed on the display. Now the activated program will be
shown on the display and you can use the UP and DOWN buttons to select the desired speed in the menu item. Now, press ENTER (the last two digits
on the display will flash) and using the UP and DOWN buttons, select the speed from SP00 to SP99. After confirming with ENTER, "SAVE" is briefly
displayed on the display.
-> ENTER ->
<- MODE
MUSIC CONTROL (SOUND)
Select the Music control mode, to control the Moving Head via the built-in microphone (bass pulses). Press the MODE button repeatedly until "dMX",
"PrEF", "SLAV", "Soun", or "Auto" appears on the display. Now use the UP and DOWN buttons to select the "Soun" menu item and confirm by
pressing ENTER ("SAVE" is briefly displayed on the display). Press ENTER again to select the sensitivity with which the spotlight responds to sounds
(Su00 - Su99). After confirming with ENTER, "SAVE" is briefly displayed on the display.
-> ENTER ->
<- MODE
SLAVE MODE
Press the MODE button repeatedly until "dMX", "PrEF", "SLAV", "Soun", or "Auto" appears on the display. Use the UP and DOWN buttons to select
the "SLAV" menu item and confirm by pressing ENTER. Use the UP and DOWN buttons to select "YES" and confirm by pressing ENTER ("SAVE" is
briefly displayed on the display). Connect the slave and the master unit (same model) with a DMX cable and activate one of the standalone modes on
the master unit. Now the slave unit follows the master unit.
SYSTEM SETTINGS
To adjust system settings, press the MODE button repeatedly until "dMX", "PrEF", "SLAV", "Soun", or "Auto" appears on the display. Use the UP and
DOWN buttons to select the "PrEF" menu item and confirm by pressing ENTER. You can now select and adjust one of the following menu items using
the UP and DOWN buttons (confirm with ENTER, exit with MODE):
14
UP/DOWN
UP/DOWN
UP/DOWN
UP/DOWN
-> ENTER ->
UP/DOWN
<- MODE
UP/DOWN
-> ENTER ->
ENTER
<- MODE
UP/DOWN