Herunterladen Inhalt Inhalt Diese Seite drucken

Unpacking - DeWalt DW079 Originalbetriebsanleitung

Vorschau ausblenden Andere Handbücher für DW079:
Inhaltsverzeichnis

Werbung

Verfügbare Sprachen
  • DE

Verfügbare Sprachen

  • DEUTSCH, seite 23
Using an Extension Cable
An extension cord should not be used unless
absolutely necessary. Use an approved extension
cable suitable for the power input of your charger
(see technical data). The minimum conductor size is
1 mm
2
; the maximum length is 30 m.
When using a cable reel, always unwind the cable
completely.

Unpacking

FITTING THE WARNING LABEL
The safety warnings on the label shown on the laser
must be formulated in the language of the user.
For that purpose, a separate sheet of self-adhesive
labels has been supplied with the tool.
WARNING: Check that the safety
warnings on the label have been
formulated in your language.
The warnings should read as follows:
LASER RADIATION
AVOID DIRECT EYE EXPOSURE
CLASS 3R LASER PRODUCT
• If the warnings are in a foreign language,
proceed as follows:
– Remove the required label from the sheet.
– Carefully place the label over the existing
label.
– Press the label in place.
ASSEMBLY
WARNING: Prior to assembly and
adjustment, always remove the battery
pack. Always switch off the tool before
inserting or removing the battery pack.
WARNING: Use only D
packs and chargers.
Inserting and Removing the
Battery Pack from the Tool (fi g. 2)
TO INSTALL THE BATTERY PACK
1. Release latch (c) to open the hatch door (a).
Insert the battery pack (v).
CAUTION: The laser will operate even
if battery door is not fully latched. To
secure the battery, always ensure
battery door is closed and latched.
2. Slide the battery pack in firmly.
3. Close the hatch door and fasten latch.
TO REMOVE THE BATTERY PACK
1. Release latch to open the hatch door.
2. Remove the battery pack.
3. Insert battery pack into the charger to recharge
it. (Refer to Charging Procedure.)
Setting Up the Laser
The laser facilitates various set-ups, making it useful
for several applications.
MANUAL HEAD ROTATION
The laser is designed with a protective alloy cage
around the rotary head to prevent accidental
damage from work site activities. You can still
access the rotary head and manually direct the
beam to establish or transfer a mark.
WALL SET-UP (FIG. 3)
The wall mount is used for mounting the laser to a
wall track to aid in drop ceiling installation and other
specialty levelling projects.
1. Place the laser on the mounting base (aa),
aligning the hole (kk) on the bottom of the laser
with the hole (bb) in the mounting base. Turn
the mounting knob (cc) to secure the laser.
2. With the wall mount measuring scale (dd) facing
you, loosen the wall mount clamp locking knob
(ee) to open the clamp jaws.
3. Position the clamp jaws around the wall track
or ceiling angle and tighten the wall mount
clamp locking knob (ee) to close the clamp
jaws onto the track. Be sure that the wall mount
clamp locking knob is securely tightened before
proceeding.
WALT battery
E
4. Using the base leveling knob (gg), approximate
a level position from the wall.
CAUTION: Before attaching the laser
level to wall track or ceiling angle, be
sure that the track or angle is properly
secured.
CAUTION: Always use a ceiling wire
hanger or equivalent material, in addition
to the wall mount clamp locking knob,
to help secure the laser level while
mounting it to a wall. Thread the wire
through the handle of the laser level.
DO NOT thread the wire through the
protective metal cage. Additionally,
screws may be used to fasten the wall
mount directly to the wall as a back-up.
Screw holes (ff) are located at the top of
the wall mount.
EN GL IS H
45

Quicklinks ausblenden:

Werbung

Inhaltsverzeichnis
loading

Inhaltsverzeichnis