Inhaltsverzeichnis
Werbung
Kenndaten der CXL-,DXL- und MXL-Suchgeräte
Die CXL-, DXL- und MXL-Suchgeräte von C.Scope sind Suchgeräte zum
Aufspüren von Rohrleitungen und Kabeln, die genaue Informationen über die
Lage und die Tiefe (nur DXL und MXL ) von unterirdischen Leitungen geben
können. Die Kombination der Ortungsmodi stellt sicher, dass unterirdische
Leitungen schnell und zuverlässig erkannt werden.
Cable Avoidance Tool
C.SCOPE International Ltd
C.SCOPE International Ltd
Kingsnorth Technology Park
Kingsnorth Technology Park
Wotton Road
Wotton Road
Ashford Kent TN23 6LN
5
0 6 0 0 8 6
3 5 0 6 6 1
Ashford Kent TN23 6LN
United Kingdom
United Kingdom
Tel. +44 (0)1233 629181
Tel. +44 (0)1233 629181
Fax +44 (0)1233 645897
Fax +44 (0)1233 645897
info@cscopelocators.com
info@cscopelocators.com
cscopelocators.com
cscopelocators.com
Warning
Read Manual
Basic Operating Instructions
Read the Instruction Manual Before Use
CAUTION
CAUTION
This Locator will find most services that radiate a detectable field. There may be some
This Locator will find most services that radiate a detectable field. There may be some
services that do not radiate and cannot be found. Once a service is located always
services that do not radiate and cannot be found. Once a service is located always
check for others nearby. Multiple services in close proximity can affect the apparent
check for others nearby. Multiple services in close proximity can affect the apparent
location of these services.
location of these services.
BATTERY CHECK
BATTERY CHECK
Switch the Locator on by pulling up on the On/Off trigger
Switch the Locator on by pulling up on the On/Off trigger
OK
Replace
under the handle. Check for audible tone and the battery
under the handle. Check for audible tone and the battery
level indicator in the bottom left hand corner of the display.
level indicator in the bottom left hand corner of the display.
Replace batteries if necessary.
Replace batteries if necessary.
Do not leave discharged batteries in the equipment.
Do not leave discharged batteries in the equipment.
WARNING Do not change batteries in confined spaces where gas may be present.
WARNING Do not change batteries in confined spaces where gas may be present.
SEARCHING IN POWER (P), RADIO (R) AND ALL SCAN (AS) MODES
SEARCHING IN POWER (P), RADIO (R) AND ALL SCAN (AS) MODES
1. Turn the Mode Switch to the appropriate mode.
1. Turn the Mode Switch to the appropriate mode.
2. Hold in the On/Off trigger. The Locator should emit the audible battery test tone
and the digital display should come on. Check the battery level indicator to confirm
2. Hold in the On/Off trigger. The Locator should emit the audible battery test tone
the batteries are usable.
and the digital display should come on. Check the battery level indicator to confirm
the batteries are usable.
3. Rotate the Sensitivity Control fully clockwise to maximum
setting as indicated by the arrow on the control.
3. Rotate the Sensitivity Control fully clockwise to maximum
4. Carry out the search using a grid pattern as shown
setting as indicated by the arrow on the control.
in the diagram. Walk slowly and keep the Locator
4. Carry out the search using a grid pattern
upright at all times and stationary by your side.
as shown in the diagram. Walk slowly
5. As you approach the area in which there
and keep the Locator upright at all
is a signal the Locator will emit an audible
times and stationary by your side.
response and show a visual response
on the display.
5. As you approach the area in which
there is a signal the Locator will emit
an audible response and show a visual
PINPOINTING
response on the display.
1. Walk through the area of the signal
response. If the visual response goes up
PINPOINTING
off the scale reduce the sensitivity slightly.
1. Walk through the area of the signal
2. The width of the signal response will
response. If the visual response goes up
shrink as the sensitivity is reduced. Once
off the scale reduce the sensitivity slightly.
it is reduced enough then a peak response
will be seen on the display as the Locator
2. The width of the signal response will
is moved back and forth over the service.
shrink as the sensitivity is reduced. Once
it is reduced enough then a peak response
3. Mark this peak response position.
will be seen on the display as the Locator
TRACING
is moved back and forth over the service.
1. Carefully follow the direction of the signal always holding the Locator at right angles
3. Mark this peak response position.
to the line of the signal. Constantly move the Locator back and forth across the service
as shown in the diagram above to be sure of still being over the peak signal.
TRACING
2. Stop and mark the position of the signal at regular intervals. As more marks are recorded
1. Carefully follow the direction of the signal always holding the Locator at right angles
the precise direction of the service will become more apparent.
to the line of the signal. Constantly move the Locator back and forth across the service
as shown in the diagram above to be sure of still being over the peak signal.
SEARCHING IN GENERATOR (G) MODE
The search pattern used to find the Generator signal is slightly different to that used
2. Stop and mark the position of the signal at regular intervals. As more marks
on Power, Radio or All Scan Modes.
are recorded the precise direction of the service will become more apparent.
DIRECT CONNECTION
SEARCHING IN GENERATOR (G) MODE
1. Move a few paces away from where the Generator has been connected to the
The search pattern used to find the Generator signal is slightly different to that used
service. Turn the Mode Switch to Generator Mode (G) and hold the Locator so that
on Power, Radio or All Scan Modes.
the side is facing towards the Generator.
2. Adjust the Sensitivity so that the Locator is just showing
DIRECT CONNECTION
a visual response and emitting an audible response.
1. Move a few paces away from where the Generator has been connected to the
service. Turn the Mode Switch to Generator Mode (G) and hold the Locator so that
3. Walk in a COMPLETE circle around the connection
the side is facing towards the Generator.
point trying to keep the same distance from this point
at all times. When a signal is detected, 'pinpoint' that
2. Adjust the Sensitivity so that the Locator is just showing
signal as shown in the 'Pinpointing' section above.
a visual response and emitting an audible response.
4. Having pinpointed the first signal, do NOT re adjust
3. Walk in a COMPLETE circle around the
the Sensitivity Control but continue with the circle to
connection point trying to keep the same distance
see if any other signals are detected.
from this point at all times. When a signal is
INDUCTION
detected, 'pinpoint' that signal as shown in the
Searching in induction mode is the same as for direct connection
'Pinpointing' section above.
except that the search is in a straight line across the end of the
4. Having pinpointed the first signal, do NOT
Generator and at least 10 metres away.
re adjust the Sensitivity Control but continue with
the circle to see if any other signals are detected.
DEPTH MEASUREMENT WITH A GENERATOR
1. The Generator should be set to 'Continuous' and is best in Connected Mode.
INDUCTION
Searching in induction mode is the same as for
2. Set the Locator to Generator Mode. Rest the Locator on the ground above and AT RIGHT
direct connection except that the search is in a
ANGLES TO the line of the service.
straight line across the end of the Generator
3. Press and hold down the depth button. The depth will be shown in metres.
and at least 10 metres away.
10 metres
DEPTH MEASUREMENT WITH A SONDE
1. Carefully pinpoint the EXACT position of the Sonde.
2. Rest the Locator on the ground above and IN LINE WITH the Sonde.
3. Push the depth button TWICE and hold on the second push. 'SONDE' will flash on the
display and the depth will then be shown in metres.
4
Depth Measuring
Cable Avoidance Tool
C.SCOPE International Ltd
Kingsnorth Technology Park
Wotton Road
Ashford Kent TN23 6LN
5
0 6 0 0 8 6
3 5 0 6 7 8
United Kingdom
Tel. +44 (0)1233 629181
Fax +44 (0)1233 645897
info@cscopelocators.com
cscopelocators.com
Warning
Read Manual
Warning
Read Manual
Basic Operating Instructions
Read the Instruction Manual Before Use
OK
Replace
Precision Pipe & Cable Locator
10 metres
Digitale Anzeige
mit automatischer
Hintergrundbeleuchtung
Abnehmbarer Lautsprecher
Ein/Aus-Schalter
Empfindlichkeitsregler
Betriebsartenschalter mit 4 Positionen
G/T: Messsender/Sender
Batteriefach
Ersetzbarer Verschleißfuß
P: Strom
R: Funk
A: All Scan
- Quicklinks:
- All Scan-Modus
Quicklinks ausblenden:
Werbung
Inhaltsverzeichnis
