AEG AR 4030 BT/USB/CR Bedienungsanleitung Seite 52

English
52
52
Pairing Devices (PAIRING)
Before you can use the car radio to make phone calls, you
must pair the units.
1. Press the MODE button to select the BT mode. BT
starts flashing on the display. This indicates that the
device is in pairing mode.
2. Select the Bluetooth menu in your mobile phone and
register the car radio in your mobile phone. To do so, re-
fer to the user manual of your mobile phone. The device
"AEG AR 4030" is selected on your mobile phone.
3. Depending on the device manufacturer, model and
software versions, now enter the password "0000" in your
mobile phone.
If the unit has been logged in successfully, BT will be shown
in the display, and MEDIA will be indicated.
NOTE:
• Depending on the mobile phone manufacturer, you
must execute the (PAIRING) message again to pair your
mobile telephone to the car radio.
• Bluetooth compatibility cannot be guaranteed for
mobile phones which may be available on the market
in future.
• To guarantee an optimum connection, make sure that
the battery of your mobile phone is fully charged.
• Some makes of mobile phone have a power saving
mode. Please deactivate power saving mode since oth-
erwise problems may arise when phoning via Bluetooth.
• To conduct an incoming or outgoing conversation, you
must keep Bluetooth activated on your mobile phone.
Please refer to the user manual of your mobile phone.
• Please make sure that you speak towards the integrated
microphone (4). An external microphone cannot be
connected.
Disconnecting the Devices
The devices are disconnected when you switch off the car
radio via the ignition or on the unit.
Reconnecting the Devices
This unit supports automatic reconnection.
Requirements are:
• the devices have already been paired
• Bluetooth is activated in your mobile telephone
• your mobile telephone supports this function.
After the car radio has been switched off and switched on
again via the ignition or on the unit, automatic reconnection
is activated.
If a connection has been established, BT will light up on the
display.
Redial
The unit stores the last dialed number. To access this, pro-
ceed as follows:
AR4030BT-USB-CR_IM
Press and hold the BAND button. CALLING will appear
on the display.
End Call
Press the CLK button to end outgoing or incoming calls.
END is shown on the display.
NOTE:
Press the CLK button also to reject an incoming call.
Incoming Call
If you receive an incoming call, the ring tone sounds from
the speakers and if the caller has a CLIP "Calling Line
Identification Presentation (Caller ID)" capable phone, the
caller number appears on the car radio display. Otherwise,
"0 0 0 0" appears on the display.
To answer an incoming call, press the
can hear the caller via the loudspeaker in your car.
Music Playback via A2DP
(Advanced Audio Distribution Profile)
This involves a cross-manufacturer Bluetooth profile.
Stereo-audio signals are transmitted wireless via streaming
between the playback unit (source) and receiver unit. To
control the source remotely, the playback unit must support
the AVRCP profile (Audio Video Remote Control Profile).
Full functionality cannot be guaranteed due to the different
unit manufacturers, models and software versions.
• After you have connected the units to each other, start
playing the music in your mobile phone. "A2DP" will
appear on the display.
• Use the button or
music title.
• Press the 1 button to pause the music playback (pause
feature). "MEDIA" will appear on the display. Press the
button again to cancel the feature.
Cleaning
Safety Advice
CAUTION:
Possible damage to the unit
Ensure that no moisture gets into the unit during cleaning
to prevent irreparable damage to the unit.
Cleaning
Always clean the housing with a slightly damp cloth.
Troubleshooting
This chapter contains important advice on identifying faults
and troubleshooting. Follow the instructions to prevent
hazards and damage.
BAND button. You
to select the next or previous
05.07.16