Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
3. "WT 2" installation into Fine Arts Vision MFW 82-710/9 DVD and MFW 82-720/9 DVD sets:
Possible variants:
EPROM version no. 29798-102.06:
From EPROM version no. 29798-102.07 on: wireless rear transmission (mono) possible.
From EPROM version no. 29798-102.10 on: wireless rear transmission (mono) possible.
Calling up the EPROM version number:
Effect the following operations with the remote control.
– Using the " " button call up the "DIALOG CENTER" –> OK.
– Press the "AUX" button. In the upper left corner of the picture screen the EPROM version number is shown.
For checking or retrofitting the TV set must be opened.
– Disconnect the mains plug of the TV set.
– Pull the rear panel by back.
– Remove the rear panel.
Attention: To avoid damage to the picture tube panel and the picture tube, the rear panel is to be removed only in upward direction
because of its considerable weight. Hold the rear panel when undoing the 6 screws and lift it carefully by an amount so that it is
possible to disconnect the earthing cable and the subwoofer cable.
– Set up the Dolby-AF module 29504-204.13 in the Dealer menu (see Service Manual 720100249200).
Installation
The installation of the "WT2" is effected to the rear panel.
– Insert/lock the right-angle aerial plug
– Pull the aerial cable through the hole in the rear panel (1st row / 20th hole from the left
– Insert the aerial along with the locating pins into the rear panel (Fig. 4) and fix it with the screws
– Fix the aerial cable with 3 adhesive tapes (commonly availlable)
– Fix the mounting clip with the white cable clamps without removing the rear panel:
– Push the white cable clamp through the top hole in the mounting clip (Fig. 6).
– Bend over the cable clamp (about 1 cm from its end),
– Wrap the cable clamp around the 11th rib from the left (Fig. 6) and tighten it (Fig. 7).
– Push the second white cable clamp through the bottom left rectangular hole.
– Bend the cable clamp at right angle and at the distance of the ribs 10-12 from the left, then wrap it around these ribs
(Fig. 7).
– Push the bottom cable clamp through the right rectangular hole.
– Pull the top cable clamp through the top hole in the mounting clip then close the cable clamp.
– Position the mounting clip as shown in Fig. 8, close and tighten both cable clamps (cut off protruding ends).
– Glue in the 4 cable holders
– Engage the "WT 2" into the hook (Fig. 8) at the top and lock it in at the bottom.
– Assign the phono cables to the sockets on the "WT 2" according to the table and their marks (A/B) and select the corresponding
position of the CH-SELECT" switch.
Number of
active loudspeakers
Surround (2)
– Connect the plugs of the phono cables according to their marks (A/B) to the audio outputs of the TV set.
– Hook the leads into the cable holders
– Connect the mains cable with the EURO-plug (Fig. 5, part no. 829099131600) to the "WT 2" and finally connect it with an external
mains socket (not with the mains socket on the TV, as this is switched off with the TV mains switch).
Fix the mains cable at the rear panel
– Insert/lock the aerial cable into the "WT 2".
– Configure the phono outputs of the TV set for the "WT 2" transmission, see user manual of the "WT 2".
– Install the active loudspeakers, see user manual of the "WT 2".
– Refit the rear panel.
14
only wireless rear transmission (mono) possible.
Wireless front transmission possible if:
– the Dolby-AF module 295042041300 is fitted,
– or the Dolby-AF module 295042040300 is fitted and the wire bridges from pin 41
to pin 39 and from pin 42 to pin 40 of the IC40305 are soldered in (Fig. 1/2).
Wireless front transmission possible if:
– the Dolby-AF module 295042041300 is fitted,
– or the Dolby-AF module 295042040300 is fitted and the wire bridges from pin 41
to pin 39 and from pin 42 to pin 40 of the IC40305 are soldered in.
The internal left and right speakers of the TV set are added on in DPL mode as centre
speaker (higher centre volume), if an additional electrolytic capacitor 2.2µF/25V ist
mounted between Pins 37/38 of IC40305 an emitter of T40420 (Fig. 1/2).
Attention: On Fine Arts Audion operation the TV set have to be muted or switched off.
A
(Fig. 3) into the socket on the aerial board
F
(Fig. 9).
Sockets "B"
left
right
1
X
X
2
X
X
3
X
X
4
X
X
F
(Fig. 9).
(Fig. 9) with a cable clamp.
G
E
, (Fig. 4).
Sockets "A"
Switch position
left
right
CH-SELECT
1
2
2
X
3
X
4
B
, (Fig. 3).
C
, Fig. 4).
D
, (Fig. 4).
Examples for
active loudspeakers variant
Mono Rear
2 Mono Rear
2 Stereo Front or Rear
2 Stereo Front and Mono Rear
2 Stereo Front and 2 Mono Rear
Werbung
Kapitel
Inhaltsverzeichnis
