Mfw 92-6110/9 Dvd Sets - Grundig WT2 Montageanleitung

2. "WT 2" installation into LENARO 82 MFW 82-6210/9 Dolby, 82 MFW 82-6210/9 IDTV,
82 MFW 82-6211/9 DVD und 92 MFW 92-6110/9 DVD sets
The installation is effected in the rear panel.
– Call up the software version number: press the " " button and then the green button on the remote control. The software version
number appears in the bottom left corner of the picture screen. This must be equal to or higher 29798-119.48. If this is not the case,
the software must be updated by programming the Flash memory.
– Disconnect the mains plug from the TV set.
– Remove rear panel cover by pulling it back.
– Because of the offset of the gravity centre when removing the rear panel, the set must be protected against tipping.
Undo 13 screws in the rear panel then remove the rear panel.
– Disengage the connector of the subwoofer on the Click-Fit component (ST-TT1).
N
– Cut out the fourth rib
A
– Bore the hole (Fig.1) in the rear panel using a 9mm drill.
– Thread the aerial cable through the aerial board (Fig. 2) and insert/lock the right-angle aerial plug into the socket
– Fit the aerial board into the rear panel (onto the locating pins
– Put the aerial thread from the outside through the rear panel. Slide the spring washer
(Fig. 2). Screw the second nut G (Fig. 2) on the aerial thread then counter-lock (VDE Safety) the two nuts.
P
– Fix the mounting clip
– Engage the "WT 2" into the hook at the top and lock it at the bottom.
– Glue in the 6 cable holders
– Contact all cinch cables according to their marks (A/B) on the "WT 2".
2
– Connect the I C bus cable to the "WT 2".
– Connect the mains cable (Fig. 3, part no. 292104356301) to the "WT 2" and hook it into the cable holder
– Lay all cables as shown in Fig. 5. Lead the cinch and the I
routing assures VDE safety.
– Glue in the 2 cable holders
– Fish the aerial cable behind the phono cable
(Fig. 5). Glue in the cable holder so that the aerial cable is stretched.
Attention: the aerial cable must fit close to the rear panel so that the safety distance to the high tension clip is assured.
R
– Glue the cable holder
– Connect the mains cable with the plug base ST-Netz1-1 (Fig. 6) on the mains switch board and hook it into the cable holder R
(Fig.8).
Safety hint: this connection remains under voltage even when the mains switch is set to "off".
– Refit the rear panel then fix it with the 13 screws.
– Connect the plugs of the phono cables according to the marks (A/B, see table) to the audio outputs (Fig. 7) of the TV set.
2
– Insert the I C bus cable into the "WT 2" connector on the TV set (Fig. 7).
– Install the active loudspeakers, see user manual of the "WT 2".
Hint: If disturbing sound noises should occur when switching the TV set with the mains switch off, a capacitor of 4.7µF/50V must
be soldered against ground into the D-amplifier (AC3 module) at the CIC40020, pin 10/11 (observe polarity, see Fig. 9/10).
Fig. 1
Fig. 3
12
(Fig. 5) with a side-cutting pliers from inner side of the rear panel (remove the burr).
(hook at top, Fig. 4) of the "WT 2" with 2 screws to the studs in the rear panel.
K L
(Fig. 5).
H
(Fig. 5) and hook in the aerial cable.
(Fig. 5) and connect it at the "WT 2". Hook the aerial cable into the cable holder
J
(Fig.8) onto the right flap mechanism.
Audio outputs of the TV set
L/R Front
L/R Surround
A
B
, Fig. 2) then fix it with the 2 screws
E
2 C bus cables out through the opening
Sockets of the WT 2
"B" "A"
left right left
X X
X
B
Fig. 2
Hook
Fig. 4
C
(Fig. 2).
on the aerial thread then fix with the nut
L
(Fig. 5).
N
(Fig. 5) of the set. This cable
right
X
G
F
E
C C
D
P
D
.
F
I
B