Safety Precautions - Ryobi ERH-650V Bedienungsanleitung

GB
FR DE ES IT
SPECIAL RULES
Wear ear protectors with impact drills. Exposure to
■
noise can cause hearing loss.
Use auxiliary handles supplied with the tool. Loss
■
of control can cause personal injury.
Advice to wear a dust mask.
■

SAFETY PRECAUTIONS

Important
To protect yourself from the risk of electric shock,
injury and fire when using an electric tool, it is
imperative to take the following basic safety
precautions. Before you use your tool, read these
instructions carefully and make sure that you
understand them thoroughly.
Make sure that the supply voltage (Volts) used
■
corresponds to the voltage marked on the tool's rating
plate.
When using cable drums, run all the cable off the
■
drum. Minimum cable across section: 1.0 mm.
When using the electric hammer drill outdoors,
■
connect it to an outdoor-grade extension cable type
H07RN-F 2G, 1.0 mm and rain-water-protected plugs
in proper working order.
Make sure of your footing when drilling freehand.
■
Before drilling,use a line detector to locate concealed
■
electric, water or gas lines in walls. Avoid touching
live components or conductors.
Wear goggles and use a dust mask on jobs
■
generating dust.
Do not use your hammer drill near flammable liquids
■
or gases.
Always pull the plug out of the socket before cleaning
■
your tool or changing accessories.
Keep the power cable in good condition. Oil and acid
■
can damage the cable.
Never overload the tool.
■
Make sure your workplace is safe.
■
Important
It is imperative to follow all national safety
regulations concerning installation, operation and
maintenance of the tool.
If incorrectly fitted, chisel bits and drill bits may be
■
flung out of the tool accidentally and cause serious
injury. Before you start using your hammer drill,
always check that the chisel or drill bit is properly
locked in the chuck.
ERH-650V&ERH-750V 24lag-ok.indd Sec1:1 ERH-650V&ERH-750V 24lag-ok.indd Sec1:1
NL PT DK SE FI NO
English
RU PL CZ HU RO LV
Examine the chuck regularly for signs of wear or
■
damage.
Always press the hammer drill against the work
■
surface (wall, ceiling, etc.) before you start it.
When you are finished, unplug the hammer drill from
■
the power supply and remove the chisel or drill bit.
Always disconnect the hammer drill from the power
■
supply before you change the chisel or drill bit.
Wear safety goggles to protect your eyes from flying
■
particles and splinters. Have other workers do the
same. Wear a helmet and put up partition walls in
your work place!
Wear work gloves to protect fingers from bruising and
■
grazing.
Vibrations can injure the hand-arm system. Keep
■
exposure to vibrations as short as possible.
Always keep the power cord behind the tool.
■
Store the tool out of the reach of children.
■
When using the tool, always hold it with both hands
■
and ensure that you have stable footing.
Chisels may only be used with ERH-750V with
■
Rotostop engaged.
Chisels may not be used with the ERH-650V, as this
■
model does not have Rotostop feature.
Wear ear protectors. Exposure to noise can cause
■
hearing loss.
Use auxiliary handles supplied with the tool. Loss
■
of control can cause personal injury.
SPECIFICATION
ERH-650V(230V) ERH-650V(110V)
Voltage 230 V 50 Hz
AC only
Power consumption 650 W
0 - 1100 min -
No load speed
Maximum drilling capacity:
- steel 13 mm
- concrete / stone 20 mm
Tool attachment SDS-plus
Weight 3.20 kg
ERH-750V(230V) ERH-750V(110V)
Voltage 230 V 50 Hz
AC only
Power consumption 710 W
0 - 1100 min -
No load speed
Maximum drilling capacity:
- steel 13 mm
1
LT EE HR SI SK GR
110 V 50 Hz
AC only
650 W
0 - 1100 min -
1 1
13 mm
20 mm
SDS-plus
3.20 kg
110 V 50 Hz
AC only
650 W
0 - 1100 min -
1 1
13 mm
6/24/09 6:01:32 PM 6/24/09 6:01:32 PM
TR