Steam Ironing; Possible Cause; Technical Data - BOMANN dbs 769 r cb Bedienungsanleitung

Steam Ironing

WARNING:
The steam brush and the iron eject a large quantity of hot
steam. Danger of burns.
CAUTION:
When using the steam iron please ensure that the water tank
is always fi lled to the required level. Operating the device
without water will damage it.
• Fill the tank up to the maximum mark. Do not overfi ll!
• Close the water tank and put it back on the base.
• Connect the base station to a 230 V / 50 Hz socket with
earthing contact.
• Turn on the switches (11) and (12).
• Set the desired temperature.
• When the control lamp (9) on the base lights up you can
start ironing.
• Press the steam jet button if necessary.
NOTE:
Keep a cloth ready! At fi rst water may also be expelled from
the soleplate of the iron.
How can I replenish the water during operation?
Refi ll with water before the tank is completely empty. The lamp
(10) shows that there is not enough water.
• Place the iron on the heel rest.
• Turn off the steam with the switch (11).
• You can remove the tank and then fi ll it up.
• Replace the tank on the base. You can now continue
operation.
Operating the steam Brush
WARNING: DANGER OF BURNS!
• Particularly when using the steam brush it is advisable to
protect yourself, e.g. by means of protective goggles, long-
armed clothing, gloves etc.
• Please also note our other warnings and instructions for
use.
NOTE:
The steam brush has a catch with which you can remove the
brush attachment.
You can use the steam brush to refresh or remove creases from
the clothes, or brush them off under steam.
For this purpose it is best to put your clothes on a hanger.
• While you are using the brush, guide it gently over the
laundry.
• If you are using only the jet of steam the distance should be
approximately 2-3 cm.
05-DBS 769 R CB.indd 33 05-DBS 769 R CB.indd 33
When you have fi nished
• After use, always turn the temperature control to „MIN" (the
control lamp in the handle of the iron goes off).
• Turn the switches (11) and (12) off.
• Remove the mains plug from the socket.
• Empty the water tank.
• Allow the device to cool down before you put it away.
Cleaning
• Always remove the mains lead before cleaning!
• Wait until the machine has cooled down completely.
• Clean the casing with a slightly damp cloth.
• Clean the sole plate and the rest with a slightly damp cloth.
Do not use any abrasive cleaning agents!
• The device must never be immersed in water!
Troubleshooting
Fault

Possible Cause

Device does not Faulty mains socket
work
Loud noises The tank is empty
during steam
operation
During steam • The temperature
operation water control on the iron
is also expelled is set too low
• It is possible that at
fi rst water will also
be expelled
The device Is the electric circuit
suddenly stops overloaded?
working during
operation

Technical Data

Model: .................................................................... DBS 769 R CB
Power supply: ............................................................230 V, 50 Hz
Power consumption: .......................................................... 2100 W
Protection class: ........................................................................... Ι
Maximum fi lling quantity of the water tank: ...................... 1,2 litres
Net weight: ...........................................................................3,7 kg
This device has been tested according to all relevant current
CE guidelines, such as electromagnetic compatibility and low
voltage directives, and has been constructed in accordance with
the latest safety regulations.
Subject to technical changes without prior notice!
Remedy
Try another socket
Check the tank
• Select a higher
temperature
• Press the steam jet
button for approx.
1 minute until no
further water comes
out
Check the house fuse
33
24.09.2007 16:01:07 Uhr 24.09.2007 16:01:07 Uhr