HQ Power VDP3000SMN Bedienungsanleitung Seite 3

4. . Insta allation
• Have the d device instal
• The carryin ng construct
deforming .
• Never stan nd directly be
technician check the d
• Install the device in a
• Adjust the desired incl
• Make sure there is no
• Connect th he device to
• The installa ation has to
5. . Use
Th e smoke ma achine is con
5.1 1 DMX 5 512 Connec
Co onnect the pr rovided XLR
XL LR output of your control
the e male 3-pin n XLR input o
Mu ultiple VDP3 3000SMNs c
lin king. The lin nking cable s
scr reened cable e with XLR in
con nnectors.
Ple ease refer to o the diagram
5.2 2 DMX-5 512 Chain w
5.3 3 Projec ctor DMX st
All DMX-contro olled devices
ad dress is the channel num
nu mber and re ead it from t
Yo u can use th he same star
Wh hen all devic ces have the
cha annel. In oth her words: c
dif fferent addre esses, each d
cha annel will on nly affect the
In the case of the 1-chann
thi rd is 3.
V. 06 – 15/05/2 012
VDP3000SM V
led by a qua alified person
tion must be e able to sup
elow the dev vice when it
evice once a a year and o once before y
location with h few passer
ination angl e via the mo
flammable m material with
the mains w with the pow
be approve d by an expe
ntrolled by 1 DMX channe
ctions
cable to the e female 3-p
ller and the other side to
of the VDP3 3000SMN.
can be linked d through se
should be tw wo core,
nput and out tput
m at the righ ht.
with termin nation
A DMX term minator is re ecommended
a long dista ance or is in
terminator prevents co orruption of t
DMX termin nator is simp
which is th en plugged i
Please see illustrations
tart addres ss selection n
s need a star rt address so
mber from w which the dev
he display lo ocated on th
rting address s for a whole
same addre ess, all the u
changing the e settings of
device will "l listen" to a s
e device in q question.
nel VDP3000 0SMN, the s
MN
n, respecting g EN 60598-
port 10 time es the weigh ht of the dev
is being mo unted, remo
you bring it i
rs-by that is inaccessible
ounting brac cket and tigh hten the brac
hin a 50cm r radius of the e device.
er plug.
ert before th he device is t
el: CHANNEL L 1 = output
in
o
erial
d for installat
an electrica ally noisy env
the digital co
ply an XLR p plug with a 1 120Ω resisto
into the XLR R output sock
to the left.
o that the co orrect device e responds to
vice starts to o "listen" to
e base of th e VDP3000 0SMN.
e group of d evices or en
units will "list ten" to the c
one channe l will affect a
separate cha annel numbe er. Changing
start address s of the first
3
2-17 and all l other applic
ice for 1 hou
oved or serv iced. Have a a qualified
into service.
e to unautho orised person
cket screws.
taken into se ervice.
channel.
tions where the DMX ca
vironment (e e.g. discos).
ontrol signal by electrica al noise. The
r between p
ket of the las st device in
o the signals
the DMX con ntroller. Ente
ter an indivi idual one for
control signa al on one par
all devices s imultaneous sly. If you se
the settings
t unit is 1, th he second un
cable norms s.
ur without
ns.
ble has to ru un
The
ins 2 and 3,
the chain.
s. This start
er the correc ct
r every devic ce.
rticular
et
s of one
nit is 2, the
©Velleman n nv