Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
18 | English
Safety warnings specific for wire brushing operations
Be aware that wire bristles are thrown by the brush
even during ordinary operation. Do not overstress the
wires by applying excessive load to the brush. The wire
bristles can easily penetrate light clothing and/or skin.
If the use of a guard is recommended for wire brushing,
do not allow any interference of the wire wheel or
brush with the guard. Wire wheel or brush may expand in
diameter due to work load and centrifugal forces.
Additional safety warnings
Wear safety goggles.
Use suitable detectors to determine if utility lines are
hidden in the work area or call the local utility company
for assistance. Contact with electric lines can lead to fire
and electric shock. Damaging a gas line can lead to explo-
sion. Penetrating a water line causes property damage or
may cause an electric shock.
Release the On/Off switch and set it to the off position
when the power supply is interrupted, e. g., in case of a
power failure or when the mains plug is pulled. This pre-
vents uncontrolled restarting.
Do not touch grinding and cutting discs before they
have cooled down. The discs can become very hot while
working.
Secure the workpiece. A workpiece clamped with clamp-
ing devices or in a vice is held more secure than by hand.
Products sold in GB only: Your product is fitted with a
BS 1363/A approved electric plug with internal fuse (ASTA
approved to BS 1362).
If the plug is not suitable for your socket outlets, it should be
cut off and an appropriate plug fitted in its place by an author-
ised customer service agent. The replacement plug should
have the same fuse rating as the original plug.
The severed plug must be disposed of to avoid a possible
shock hazard and should never be inserted into a mains sock-
et elsewhere.
Products sold in AUS and NZ only: Use a residual current de-
vice (RCD) with a rated residual current of 30 mA or less.
Product Description and Specifica-
tions
Read all safety warnings and all instruc-
tions. Failure to follow the warnings and in-
structions may result in electric shock, fire
and/or serious injury.
While reading the operating instructions, unfold the graphics
page for the machine and leave it open.
Intended Use
The machine is intended for cutting, roughing and brushing of
metal and stone materials without the use of water.
1 609 92A 0MJ | (23.4.14)
For cutting with bonded abrasives, a special cutting guard
(accessory) must be used.
When cutting in stone, provide for sufficient dust extraction.
With approved sanding tools, the machine can be used for
sanding with sanding discs.
Product Features
The numbering of the product features refers to the illustra-
tion of the machine on the graphics page.
1 Spindle lock button
2 On/Off switch
3 Auxiliary handle (insulated gripping surface)
4 Grinder spindle
5 Protection guard for grinding
6 Locking screw for protection guard
7 Mounting flange with O-ring
8 Grinding wheel*
9 Clamping nut
10 Two-pin spanner for clamping nut*
11 Quick-clamping nut
12 Carbide grinding head*
13 Protection guard for cutting*
14 Cutting disc*
15 Protection guard for grinding cup*
16 Grinding cup*
17 Two-pin spanner, offset, for grinding cup*
18 Hand guard*
19 Spacer discs*
20 Rubber sanding plate*
21 Sanding sheet*
22 Round nut*
23 Cup brush*
24 Cutting guide with dust extraction protection guard *
25 Diamond cutting disc*
26 Handle (insulated gripping surface)
*Accessories shown or described are not part of the standard de-
livery scope of the product. A complete overview of accessories
can be found in our accessories program.
Technical Data
Angle Grinder
GWS ...
Article number
3 601 ...
Rated power input
Output power
The values given are valid for a nominal voltage [U] of 230 V. For differ-
ent voltages and models for specific countries, these values can vary.
Only for power tools without reduced starting current: Starting cycles
generate brief voltage drops. Interference with other equipment/ma-
chines may occur in case of unfavourable mains system conditions. Mal-
functions are not to be expected for system impedances below
0.25 ohm.
*
20-230
20-230
H
JH
... H50 L.. ... H50 M..
W
2000
2000
W
1250
1250
Bosch Power Tools
Werbung
Inhaltsverzeichnis
