Inhaltszusammenfassung für IFM Electronic EFECTOR190 DTS125
Seite 1
Montageanleitung RF-Identifikationssystem mit integriertem AS-i Slave Installation instructions RF-identification system with integrated AS-i slave Notice de montage Système d‘identification RFID avec esclave AS-i intégré DTS125...
Vorbemerkung Dieses Dokument gilt für alle Geräte des Typs DTS125. Es ist Bestandteil des Gerätes und enthält Angaben zum korrekten Umgang mit dem Produkt. Dieses Dokument richtet sich an Fachkräfte. Dabei handelt es sich um Personen, die aufgrund ihrer Ausbildung und ihrer Erfahrung befähigt sind, Risiken zu erkennen und mögliche Gefährdungen zu vermeiden, die der Betrieb oder die Instandhaltung des Gerätes verursachen kann.
Bei Fehlfunktion des Gerätes oder bei Unklarheiten bitte mit dem Hersteller in Verbindung setzen. Eingriffe in das Gerät können schwerwiegende Beeinträchti- gungen der Sicherheit von Menschen und Anlagen zur Folge haben. Sie sind nicht zulässig und führen zu Haftungs- und Gewährleistungsauschluss. Funkanlagen Funkgeräte dürfen generell nicht in der Nähe von Tankstellen, Kraftstoffdepots, Chemiewerken oder Sprengarbeiten benutzt werden.
Funktion (Beispiel Lese-/Schreibkopf DTA100 und ID-TAG E80301) Typenübersicht DTA10x DTA20x DTA30x Art.-Nr. Funktion Typbezeichnung H x B x T [mm] DTA100 Lese-/Schreibkopf DTS125 AARWASUS 55 x 24 x 41 DTA101 Lesekopf DTS125 AAROASUS DTA200 Lese-/Schreibkopf DTS125 MCRWASUS 40 x 40 x 54 DTA201 Lesekopf DTS125 MCROASUS...
Art.-Nr. Funktion Typbezeichnung H x B x T [mm] DTA300 Lese-/Schreibkopf DTS125 DCRWASUS 92 x 80 x 40 DTA301 Lesekopf DTS125 DCROASUS Montage Generelle Montagehinweise Bei der Montage von mehreren Systemen die Mindestabstände zwischen den Lese-/Schreibköpfen beachten. Der bündige Einbau eines Lese-/Schreibkopfes in Metall verringert den Lese-/Schreibabstand.
5.3.5 Lese-/Schreibabstände ID-TAG Bauform Positionierung Lesen Schreiben E80301 Frontseite E80302 5...20 E80311 E80312 5...20 E80317 10...28 E80318 15...40 Überkopf E80319 20...60 20...50 E80320 18...60 E80322 15...40 Alle Angaben gelten für statische Lese-/Schreibvorgänge. Wenn nicht anders angegeben, beziehen sie sich auf den ID-TAG Einbau in eine nicht-metallische Umgebung. Alle Angaben in mm *) ID-TAG Einbau bündig in Metall DTA20x...
5.4.2 Aktive Fläche ausrichten 180° 90° Schraube lösen. Antennenkopf vom Befestigungselement trennen und drehen. Befestigungselement und Antennenkopf Schraube anziehen. zusammenstecken. 5.4.3 Befestigung ► Das Gerät mit 2 Stk. M4 Schrauben und Muttern befestigen. Wahlweise nicht bündig oder bündig. nicht bündig bündig...
5.4.6 Ausrichtung der ID-TAGs Antennenachse DTA20x = Achse ID-TAG Antennenmitte DTA20x = Mitte ID-TAG 5.4.7 Lese-/Schreibabstände Einbau Lese-/Schreibkopf ID-TAG Bauform nicht bündig bündig in Metall E80311 E80312 E80317 E80318 E80319 E80320 E80322 Alle Angaben gelten für statische Lese-/Schreibvorgänge. Wenn nicht anders angegeben, beziehen sie sich auf den ID-TAG Einbau in eine nicht-metallische Umgebung.
DTA30x 5.5.1 Befestigung ► Das Gerät wahlweise auf einer 35 mm Normschiene oder mit 4 Stk. M5 Schrauben und Muttern befestigen. Montagebeispiel E11122 5.5.2 Montageabstände Betriebsart Abstand seitlich (A) Abstand frontal (B) Nur Lesen ≥ 280 mm ≥ 400 mm Lesen und Schreiben ≥...
ID-TAG Bauform Lesen Schreiben E80319 E80320 E80322 Alle Angaben gelten für statische Lese-/Schreibvorgänge. Wenn nicht anders angegeben, beziehen sie sich auf den ID-TAG Einbau in eine nicht-metallische Umgebung. Alle Angaben in mm 5.5.6 Steckereinsatz drehen Der Steckereinsatz ist in 45°-Schritten drehbar. 1.
Elektrischer Anschluss Anschlussbelegung ► Das Gerät über die M12-Steckverbindung mit dem AS-i-Netz verbinden. Die Spannungsversorgung erfolgt aus dem AS-i-Netz. ASI+ Anschlussbelegung und Adernfarben bei ifm-Kabeldosen 1 = BN (braun) 2 = BU (blau) Eine Auswahl an Kabeldosen ist im Internet abrufbar unter: →...
UL-Zulassung Folgender Hinweis gilt nur für die Geräte DTA20x und DTA30x. ► Das Gerät von einer galvanisch getrennten Quelle versorgen, die sekundär über eine UL-zugelassene Sicherung mit folgendem max. Nennstrom verfügt. a) 5 A bei Spannungen von 0...20 V (0...28,3 V b) 100/V bei Spannungen von 20...30 V (28,3...42,4 V...
Schreibbetrieb (nur DTA100, DTA200, DTA300) Zustand Bedeutung grün/rot EIN/AUS wie Lesebetrieb gelb EIN (Impuls) ID-TAG erfolgreich beschrieben kein ID-TAG im Feld oder fehlerhafter ID-TAG im Feld oder ungültiger ID-TAG (falsche Kennung) gelb 500 ms blinkend ID-TAG beschreiben nicht möglich – ID-TAG nicht formatiert –...
Betrieb Grundeinstellungen im AS-i Netzwerk Parameter Lese-/Schreibkopf Lesekopf DTA100, DTA200, DTA101, DTA201, DTA300 DTA301 AS-i Profil I/O Code ID Code Extended ID2 Code ID1 Code für Codewert Slave-Adresse (Werkseinstellung) Codewerte im Hex-Format Adressierung Der Lese-/Schreibkopf wird adressiert mit einem Adressiergerät (z.B. AC1144), dem Master oder mit der AS-i-Software des Hosts (die Komponenten müssen AS-i Version 2.1 unterstützen).
Codewert-Darstellung durch Datenbits D16...D1 Die Darstellung des ID-Wertes erfolgt als vorzeichenbehaftete 16 Bit Zahl. Bereich Dezimal Wertebereich 32767 7FFF Meldebereich -32768 FFFF 8000 Wert 0 = kein ID-TAG im Lesebereich oder ID-TAG nicht erkannt. Zusatzfunktionen gemäß AS-i Profil 7.4 (Nur gültig für Lese-/Schreibköpfe) Funktion, Beschreibung DTA100 DTA200 DTA300 Read ID String...
DTA30x Alle Angaben in mm Technische Daten Die Datenblätter sind im im Internet abrufbar unter: → Datenblatt-Suche → z.B. DTA100 www.ifm.com Wartung, Instandsetzung und Entsorgung ► Da innerhalb des Gerätes keine vom Anwender zu wartenden Bauteile enthal- ten sind, das Gehäuse nicht öffnen. Die Instandsetzung des Gerätes darf nur durch den Hersteller durchgeführt werden.
12.1.3 Hinweise FCC (USA, Kanada) Dieses Gerät erfüllt den Teil 15 der Bestimmungen der FCC und die RSS-210 der Industry Canada. Der Betrieb setzt die folgenden zwei Bedingungen voraus: (1) Dieses Gerät darf keine schädlichen Störungen verursachen und (2) dieses Gerät muss eine Beeinflussung tolerieren, einschließlich einer Beein- flussung, die einen unerwünschten Betrieb verursachen kann.
12.1.5 Singapur Complies with IDA Standards Db 103032 Die “Equipment Registration” ist im Internet abrufbar unter: → Datenblatt-Suche → z.B. DTA100 → Zulassungen www.ifm.com 12.2 EG-Konformitätserklärung Die EG-Konformitätserklärung ist im Internet abrufbar unter: → Datenblatt-Suche → z.B. DTA100 → Zulassungen www.ifm.com...
Seite 28
Inhalt 1 Preliminary note ....................4 1.1 Symbols used ....................4 2 Safety instructions ....................4 2.1 General ......................4 2.2 Radio equipment ..................5 2.3 Interference of electronic and medical devices ..........5 3 Functions and features ..................5 4 Function .......................5 4.1 Operating principle ..................5 4.2 Type overview ....................6 5 Installation......................7 5.1 General installation instructions ..............7...
Preliminary note This document applies to all DTA125 type units. It is part of the device and contains information about the correct handling of the product. This document is intended for specialists. These specialists are people who are qualified by their training and their experience to see risks and to avoid possible hazards that may be caused during operation or maintenance of the device.
Radio equipment In general, radio equipment must not be used in the vicinity of petrol stations, fuel depots, chemical plants or blasting operations. ► Do not transport and store any flammable gases, liquids or explosive substances near the unit. Interference of electronic and medical devices Operation can affect the function of electronic devices that are not correctly shielded.
function (example read/write head DTA100 and ID tag E80301) Type overview DTA10x DTA20x DTA30x Art. no. Function Type designation H x V x D [mm] DTA100 Read/write head DTS125 AARWASUS 55 x 24 x 41 DTA101 Read head DTS125 AAROASUS DTA200 Read/write head DTS125 MCRWASUS...
Art. no. Function Type designation H x V x D [mm] DTA300 Read/write head DTS125 DCRWASUS 92 X 80 X 40 DTA301 Read head DTS125 DCROASUS Installation General installation instructions When mounting several read/write heads adhere to the minimum distances between the systems.
DTA10x 5.3.1 Fixing ► The device is fixed via either 2 M4 screws and nuts or via an angle bracket. mounting example E20898 mounting example E20901 5.3.2 Mounting distances Operating mode Distance side (A) Distance front (B) Reading only ≥ 200 mm ≥...
5.3.3 Positioning of the ID tags front side overhead 5.3.4 Orientation of the ID tags DTA10x antenna axis = ID tag axis DTA10x middle of the antenna = middle of the ID tag...
5.3.5 Read/write distances ID tag Type Positioning Read Write E80301 front side E80302 5...20 E80311 E80312 5...20 E80317 10...28 E80318 15...40 overhead E80319 20...60 20...50 E80320 18...60 E80322 15...40 All indications apply to static read/write operations. If not otherwise stated they refer to ID tag installation in a non-metallic environment.
5.4.2 Alignment of the sensing face 180° 90° Loosen the screw. Remove the antenna head from the fixing element and turn it. Attach the fixing element to the antenna Tighten the screw. head. 5.4.3 Fixing ► The device is fixed with 2 M4 screws and nuts. Order non flush or flush.
5.4.4 Mounting distances Operating mode Distance side (A) Distance front (B) Reading only ≥ 150 mm ≥ 150 mm For reading and writing ≥ 300 mm ≥ 300 mm 5.4.5 Positioning of the ID tags E80311 E80312 E80317 E80318 E80319 E80322 E80320 front side...
5.4.6 Orientation of the ID tags antenna axis DTA20x = ID tag axis middle of the antenna DTA20x = middle of the ID tag 5.4.7 Read/write distances Installation read/write head ID tag Type Non flush Flush in metal E80311 E80312 E80317 E80318 E80319...
DTA30x 5.5.1 Fixing ► The device is fixed via either a 35 mm DIN rail or via 4 M5 screws and nuts. example mounting E11122 5.5.2 Mounting distances Operating mode Distance side (A) Distance front (B) Reading only ≥ 280 mm ≥...
5.5.3 Positioning of the ID tags E80311 E80312 E80317 E80318 E80319 E80322 E80320 front side 5.5.4 Orientation of the ID tags DTA30x antenna axis = ID tag axis DTA30x middle of the antenna = middle of the ID tag 5.5.5 Read/write distances ID tag Type...
ID tag Type Read Write E80319 E80320 E80322 All indications apply to static read/write operations. If not otherwise stated they refer to ID tag installation in a non-metallic environment. All indications in mm. 5.5.6 Rotating plug insert The plug insert can be rotated in steps of 45°. 1.
Electrical connection Wiring ► Connect the unit to the AS-i network using the M12 connector. Voltage is supplied via the AS-i network. ASI+ Wiring and core colours of ifm sockets 1 = BN (brown) 2 = BU (blue) A selection of sockets is available on our website at: →...
UL approval The following note applies to the units DTA20x and DTA30x only. ► The device shall be supplied from an isolating transformer having a secondary Listed fuse rated either a) max 5 amps for voltages 0...20 V (0...28.3 V ) or b) 100/V for voltages of 20...30 V...
Write operation (only DTA100, DTA200, DTA300) Status Description green/red ON/OFF like read operation yellow ON (pulse) ID tag written successfully no ID tag in the field or faulty ID tag in the field or invalid ID tag (wrong identification) yellow 500 ms flashing writing of the ID tag not possible –...
Operation Basic settings in the AS-i network Parameter Read/write head Read head DTA100, DTA200, DTA101, DTA201, DTA300 DTA301 AS-i profile I/O code ID code Extended ID2 code ID1 code for code value Slave address (factory setting) Code values in hex format Addressing The read/write head is addressed using an addressing unit (e.g.
Code value representation using the data bits D16...D1 The ID value is represented as a signed 16-bit number. Range Decimal from from Value range 32767 7FFF Message range -32768 FFFF 8000 Value 0 = no ID tag in the reading range or ID tag not detected Additional functions to the AS-i profile 7.4 (Applies only to read/write heads) Function, description...
DTA30x All indications in mm Technical data The data sheets are available on our website at: → Data sheet direct → e.g. DTA100 www.ifm.com Maintenance, repair and disposal ► Do not open the housing, as the device does not contain any components which must be maintained by the user.
12.1.3 FCC Notices (USA, Canada) This device complies with Part 15 of the FCC Rules and with RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1) this device must not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
12.1.5 Singapore Complies with IDA Standards Db 103032 The “Equipment Registration” is available on our website at: → Data sheet direct → e.g. DTA100 → Approvals www.ifm.com 12.2 EC Declaration of Conformity You can find the EC declaration of conformity on our website at: →...
Seite 54
Inhalt 1 Remarque préliminaire ..................4 1.1 Symboles utilisés ..................4 2 Consignes de sécurité ..................4 2.1 Général ......................4 2.2 Equipements radio ..................5 2.3 Perturbations d'appareils électroniques et médicaux ........5 3 Fonctionnement et caractéristiques ..............5 4 Fonction .......................5 4.1 Principe de fonctionnement ................5 4.2 Aperçu des types ..................6 5 Montage .......................7 5.1 Notices de montage générales ..............7...
Seite 55
6 Raccordement électrique ...................17 6.1 Schéma de branchement ................17 6.2 Distance minimale entre le câble AS-i et le boîtier ........17 6.2.1 DTA10x ....................17 6.2.2 DTA20x ....................18 6.2.3 DTA30x ....................18 6.3 Homologation UL ..................19 7 Eléments de visualisation ..................19 7.1 Fonctionnement lecture (réglage de base) ..........19 7.2 Fonctionnement écriture (uniquement DTA100, DTA200 et DTA300) ..20 8 Fonctionnement ....................20 8.1 Réglages de base dans le réseau AS-i ............20...
Remarque préliminaire Ce document s'applique à tous les appareils DTS125. Il fait partie de l'appareil et fournit des informations sur l'utilisation correcte du produit. Ce document s'adresse à des personnes compétentes. Ce sont des personnes qui sont capables - grâce à leur formation et expérience – d’apercevoir des risques et d'éviter des dangers potentiels qui pourraient être causés par le fonctionnement ou la maintenance de l'appareil.
pour la sécurité des personnes et des installations. Elles ne sont pas autorisées et aboutissent à une exclusion de responsabilité et de garantie. Equipements radio En général, les équipements radio ne doivent pas être utilisés à proximité de stations d'essence, de dépôts de carburants, d'usines chimiques ou de lieux où il existe des risques de détonation.
Fonctionnement (exemple tête de lecture/écriture DTA100 et TAG E80301) Aperçu des types DTA10x DTA20x DTA30x Référence Fonction Désignation H x L x P [mm] DTA100 tête de lecture/écriture DTS125 AARWASUS 55 x 24 x 41 DTA101 tête de lecture DTS125 AAROASUS DTA200 tête de lecture/écriture DTS125 MCRWASUS...
Référence Fonction Désignation H x L x P [mm] DTA300 tête de lecture/écriture DTS125 DCRWASUS 92 x 80 x 40 DTA301 tête de lecture DTS125 DCROASUS Montage Notices de montage générales En cas de montage de plusieurs systèmes respecter les distances minima- les entre les tètes de lecture/écriture .
DTA10x 5.3.1 Fixation ► La fixation se fait par 2 vis M4 et écrous ou par une équerre. exemple de montage E20898 exemple de montage E20901 5.3.2 Distances de montage Mode de fonctionnement Distance latérale (A) Distance frontale (B) Seulement lecture ≥...
5.3.3 Positionnement des TAG face avant au dessus de la tête 5.3.4 L'orientation des TAG axe de l'antenne DTA10x = axe du TAG milieu de l'antenne DTA10x = milieu du TAG...
5.3.5 Distances de lecture/écriture Type Positionnement Lecture Ecriture E80301 face avant E80302 5...20 E80311 E80312 5...20 E80317 10...28 E80318 15...40 au dessus de la tête E80319 20...60 20...50 E80320 18...60 E80322 15...40 Toutes les indications s'appliquent à des process lecture/écriture statiques. Sauf indications contraires, elles se réfèrent au montage du TAG dans un environnement non-métallique.
5.4.2 Orientation de la face active 180° 90° Desserrer la vis. Séparer la tête d'antenne de l'accessoire de fixation et la tourner. Placer l'accessoire de fixation sur la tête Serrer la vis. d'antenne. 5.4.3 Fixation ► La fixation se fait par 2 vis M4 et écrous ou par une équerre. Au choix encastré...
5.4.4 Distances de montage Mode de fonctionnement Distance latérale (A) Distance frontale (B) Seulement lecture ≥ 150 mm ≥150 mm Lecture et écriture ≥ 300 mm ≥ 300 mm 5.4.5 Positionnement des TAG E80311 E80312 E80317 E80318 E80319 E80322 E80320 face avant...
5.4.6 L'orientation des TAG axe de l'antenne DTA20x = axe du TAG milieu de l'antenne TA20x = milieu du TAG 5.4.7 Distances de lecture/écriture Montage de la tête de lecture/écriture Encastré dans le Type Non encastré métal E80311 E80312 E80317 E80318 E80319 E80320...
DTA30x 5.5.1 Fixation ► La fixation se fait sur rail 35 mm ou par 4 vis et écrous M5. Exemple de montage E11122 5.5.2 Distances de montage Mode de fonctionnement Distance latérale (A) Distance frontale (B) Seulement lecture ≥ 280 mm ≥...
5.5.3 Positionnement des TAG E80311 E80312 E80317 E80318 E80319 E80322 E80320 face avant 5.5.4 L'orientation des TAG axe de l'antenne DTA30x = axe du TAG milieu de l'antenne TA30x = milieu du TAG 5.5.5 Distances de lecture/écriture Type Lecture Ecriture E80311 E80312 E80317...
Type Lecture Ecriture E80319 E80320 E80322 Toutes les indications s'appliquent à des process lecture/écriture statique. Sauf indications contraires, elles se réfèrent au montage du TAG dans un environnement non-métallique. Toutes les indications en mm. 5.5.6 Orienter l'insert du connecteur L'insert du connecteur est orientable en pas de 45°. 2.
Raccordement électrique Schéma de branchement ► Raccorder la tête de lecture/écriture au réseau AS-i via le connecteur M12. L'alimentation en tension s'effectue via le réseau AS-i. ASI+ Schéma de branchement et couleurs des fils conducteurs des connecteurs femelles ifm 1 = BN (brun) 2 = BU (bleu) Une sélection de connecteurs femelles est disponible sur notre site web à...
Homologation UL La remarque suivante ne s‘applique qu‘aux appareils DTA20x et DTA30x. ► L‘appareil doit être impérativement alimenté par une alimentation isolée galvaniquement disposant au secondaire d‘un fusible avec homologation UL et un courant nominal max. de a) 5 ampères pour des tensions de 0...20 Veff (0...28.3 Vpic) ou b) 100/Vpic pour des tensions de 20...30 Veff (28.3...42.4 Vpic).
Fonctionnement écriture (uniquement DTA100, DTA200 et DTA300) Etat Signification verte/ ALLUMEE/ETEINTE comme fonctionnement lecture rouge jaune ALLUMEE (impulsion) TAG écrit avec succès ETEINTE aucun TAG dans le champ ou TAG défectueux dans le champ ou TAG non valable (identification incorrecte) jaune 500 ms clignotant écriture du TAG pas possible...
Représentation des valeurs analogiques Pour l'AS-interface la tête de lecture/écriture est un esclave ayant une entrée analogique avec le protocole de transmission selon le profil 7.4 ou 7.3 (voir ci-dessus). Si le maître travaille selon le profil maître M3 ou M4, il détecte automatiquement la tête de lecture/écriture et est compatible avec le profil 7.4.
Fonctions supplémentaires selon le profil AS-i 7.4 (S'appliquent seulement aux têtes de lecture/écriture) Fonctionnement, description DTA100 DTA200 DTA300 Read ID string (lecture de la chaîne ID) Vérifier les informations esclave AS-i ● ● ● Read Diagnosis String (lecture de la chaîne de diagnostic) Vérifier les statistiques sur des process lecture/écriture ●...
DTA30x Toutes les indications en mm. Données techniques Les fiches techniques sont disponibles sur notre site web à : → Fiche technique → par ex. DTA100 www.ifm.com Maintenance, réparation et élimination ► Ne pas ouvrir l'appareil car il ne contient pas de composants à maintenir par l'utilisateur.
Attention: Tout changement ou modification effectué sans autorisation explicite de la part d'ifm electronic gmbh peut entraîner l'annulation de l'autorisation de la part de FCC d'utiliser ces appareils. Remarque : Cet appareil a été testé et est conforme aux limites concernant les dispositifs numériques de classe B selon la partie 15 des règlements FCC.
12.1.5 Singapour Complies with IDA Standards Db 103032 Le "Equipment Registration" est disponible sur notre site web à : → Fiche technique → par ex. DTA100 → Homologations www.ifm.com 12.2 Déclaration de conformité CE La déclaration de conformité CE est disponible sur notre site web à : →...