Inhaltszusammenfassung für IFM Electronic efector190 DTS125
Seite 1
All manuals and user guides at all-guides.com Montageanleitung RF-Identifikationssystem mit integriertem AS-i Slave Installation instructions RF-identification system with integrated AS-i slave Notice de montage Système d‘identification RFID avec esclave AS-i intégré DTS125...
All manuals and user guides at all-guides.com Vorbemerkung Dieses Dokument gilt für alle Geräte des Typs DTS125. Es ist Bestandteil des Gerätes und enthält Angaben zum korrekten Umgang mit dem Produkt. Dieses Dokument richtet sich an Fachkräfte. Dabei handelt es sich um Personen, die aufgrund ihrer Ausbildung und ihrer Erfahrung befähigt sind, Risiken zu erkennen und mögliche Gefährdungen zu vermeiden, die der Betrieb oder die Instandhaltung des Gerätes verursachen kann.
All manuals and user guides at all-guides.com Bei Fehlfunktion des Gerätes oder bei Unklarheiten bitte mit dem Hersteller in Verbindung setzen. Eingriffe in das Gerät können schwerwiegende Beeinträchti- gungen der Sicherheit von Menschen und Anlagen zur Folge haben. Sie sind nicht zulässig und führen zu Haftungs- und Gewährleistungsauschluss.
All manuals and user guides at all-guides.com Funktion (Beispiel Lese-/Schreibkopf DTA100 und ID-TAG E80301) Typenübersicht DTA10x DTA20x DTA30x Art.-Nr. Funktion Typbezeichnung H x B x T [mm] DTA100 Lese-/Schreibkopf DTS125 AARWASUS 55 x 24 x 41 DTA101 Lesekopf DTS125 AAROASUS DTA200 Lese-/Schreibkopf DTS125 MCRWASUS...
All manuals and user guides at all-guides.com Art.-Nr. Funktion Typbezeichnung H x B x T [mm] DTA300 Lese-/Schreibkopf DTS125 DCRWASUS 92 x 80 x 40 DTA301 Lesekopf DTS125 DCROASUS Montage Generelle Montagehinweise Bei der Montage von mehreren Systemen die Mindestabstände zwischen den Lese-/Schreibköpfen beachten.
All manuals and user guides at all-guides.com DTA10x 5.3.1 Befestigung ► Das Gerät wahlweise mit 2 Stk. M4 Schrauben und Muttern oder mittels Klemmhalterung befestigen. Montagebeispiel E20898 Montagebeispiel E20901 5.3.2 Montageabstände Betriebsart Abstand seitlich (A) Abstand frontal (B) Nur Lesen ≥...
All manuals and user guides at all-guides.com 5.3.3 Positionierung der ID-TAGs Frontseite Überkopf 5.3.4 Ausrichtung der ID-TAGs Antennenachse DTA10x = Achse ID-TAG Antennenmitte DTA10x = Mitte ID-TAG...
All manuals and user guides at all-guides.com 5.3.5 Lese-/Schreibabstände ID-TAG Bauform Positionierung Lesen Schreiben E80301 Frontseite E80302 5...20 E80311 E80312 5...20 E80317 10...28 E80318 15...40 Überkopf E80319 20...60 20...50 E80320 18...60 E80322 15...40 Alle Angaben gelten für statische Lese-/Schreibvorgänge. Wenn nicht anders angegeben, beziehen sie sich auf den ID-TAG Einbau in eine nicht-metallische Umgebung.
All manuals and user guides at all-guides.com 5.4.2 Aktive Fläche ausrichten 180° 90° Schraube lösen. Antennenkopf vom Befestigungselement trennen und drehen. Befestigungselement und Antennenkopf Schraube anziehen. zusammenstecken. 5.4.3 Befestigung ► Das Gerät mit 2 Stk. M4 Schrauben und Muttern befestigen. Wahlweise nicht bündig oder bündig.
All manuals and user guides at all-guides.com 5.4.4 Montageabstände Betriebsart Abstand seitlich (A) Abstand frontal (B) Nur Lesen ≥ 150 mm ≥ 150 mm Lesen und Schreiben ≥ 300 mm ≥ 300 mm 5.4.5 Positionierung der ID-TAGs E80311 E80312 E80317 E80318 E80319 E80322 E80320 Frontseite...
All manuals and user guides at all-guides.com 5.4.6 Ausrichtung der ID-TAGs Antennenachse DTA20x = Achse ID-TAG Antennenmitte DTA20x = Mitte ID-TAG 5.4.7 Lese-/Schreibabstände Einbau Lese-/Schreibkopf ID-TAG Bauform nicht bündig bündig in Metall E80311 E80312 E80317 E80318 E80319 E80320 E80322 Alle Angaben gelten für statische Lese-/Schreibvorgänge. Wenn nicht anders angegeben, beziehen sie sich auf den ID-TAG Einbau in eine nicht-metallische Umgebung.
All manuals and user guides at all-guides.com DTA30x 5.5.1 Befestigung ► Das Gerät wahlweise auf einer 35 mm Normschiene oder mit 4 Stk. M5 Schrauben und Muttern befestigen. Montagebeispiel E11122 5.5.2 Montageabstände Betriebsart Abstand seitlich (A) Abstand frontal (B) Nur Lesen ≥...
All manuals and user guides at all-guides.com ID-TAG Bauform Lesen Schreiben E80319 E80320 E80322 Alle Angaben gelten für statische Lese-/Schreibvorgänge. Wenn nicht anders angegeben, beziehen sie sich auf den ID-TAG Einbau in eine nicht-metallische Umgebung. Alle Angaben in mm 5.5.6 Steckereinsatz drehen Der Steckereinsatz ist in 45°-Schritten drehbar.
All manuals and user guides at all-guides.com Elektrischer Anschluss Anschlussbelegung ► Das Gerät über die M12-Steckverbindung mit dem AS-i-Netz verbinden. Die Spannungsversorgung erfolgt aus dem AS-i-Netz. ASI+ Anschlussbelegung und Adernfarben bei ifm-Kabeldosen 1 = BN (braun) 2 = BU (blau) Eine Auswahl an Kabeldosen ist im Internet abrufbar unter: →...
All manuals and user guides at all-guides.com UL-Zulassung Folgender Hinweis gilt nur für die Geräte DTA20x und DTA30x. ► Das Gerät von einer galvanisch getrennten Quelle versorgen, die sekundär über eine UL-zugelassene Sicherung mit folgendem max. Nennstrom verfügt. a) 5 A bei Spannungen von 0...20 V (0...28,3 V b) 100/V bei Spannungen von 20...30 V...
All manuals and user guides at all-guides.com Schreibbetrieb (nur DTA100, DTA200, DTA300) Zustand Bedeutung grün/rot EIN/AUS wie Lesebetrieb gelb EIN (Impuls) ID-TAG erfolgreich beschrieben kein ID-TAG im Feld oder fehlerhafter ID-TAG im Feld oder ungültiger ID-TAG (falsche Kennung) gelb 500 ms blinkend ID-TAG beschreiben nicht möglich –...
All manuals and user guides at all-guides.com Betrieb Grundeinstellungen im AS-i Netzwerk Parameter Lese-/Schreibkopf Lesekopf DTA100, DTA200, DTA101, DTA201, DTA300 DTA301 AS-i Profil I/O Code ID Code Extended ID2 Code ID1 Code für Codewert Slave-Adresse (Werkseinstellung) Codewerte im Hex-Format Adressierung Der Lese-/Schreibkopf wird adressiert mit einem Adressiergerät (z.B.
All manuals and user guides at all-guides.com Codewert-Darstellung durch Datenbits D16...D1 Die Darstellung des ID-Wertes erfolgt als vorzeichenbehaftete 16 Bit Zahl. Bereich Dezimal Wertebereich 32767 7FFF Meldebereich -32768 FFFF 8000 Wert 0 = kein ID-TAG im Lesebereich oder ID-TAG nicht erkannt. Zusatzfunktionen gemäß...
All manuals and user guides at all-guides.com DTA30x Alle Angaben in mm Technische Daten Die Datenblätter sind im im Internet abrufbar unter: → Datenblatt-Suche → z.B. DTA100 www.ifm.com Wartung, Instandsetzung und Entsorgung ► Da innerhalb des Gerätes keine vom Anwender zu wartenden Bauteile enthal- ten sind, das Gehäuse nicht öffnen.
All manuals and user guides at all-guides.com 12.1.3 Hinweise FCC (USA, Kanada) Dieses Gerät erfüllt den Teil 15 der Bestimmungen der FCC und die RSS-210 der Industry Canada. Der Betrieb setzt die folgenden zwei Bedingungen voraus: (1) Dieses Gerät darf keine schädlichen Störungen verursachen und (2) dieses Gerät muss eine Beeinflussung tolerieren, einschließlich einer Beein- flussung, die einen unerwünschten Betrieb verursachen kann.
All manuals and user guides at all-guides.com 12.1.5 Singapur Complies with IDA Standards Db 103032 Die “Equipment Registration” ist im Internet abrufbar unter: → Datenblatt-Suche → z.B. DTA100 → Zulassungen www.ifm.com 12.2 EG-Konformitätserklärung Die EG-Konformitätserklärung ist im Internet abrufbar unter: →...
Seite 27
All manuals and user guides at all-guides.com...
Seite 28
All manuals and user guides at all-guides.com Inhalt 1 Preliminary note ....................4 1.1 Symbols used ....................4 2 Safety instructions ....................4 2.1 General ......................4 2.2 Radio equipment ..................5 2.3 Interference of electronic and medical devices ..........5 3 Functions and features ..................5 4 Function .......................5 4.1 Operating principle ..................5 4.2 Type overview ....................6...
Seite 29
All manuals and user guides at all-guides.com 6 Electrical connection ..................17 6.1 Wiring ......................17 6.2 Minimum distance between AS-i cable and housing ........17 6.2.1 DTA10x ....................17 6.2.2 DTA20x ....................18 6.2.3 DTA30x ....................18 6.3 UL approval ....................19 7 Indicators ......................19 7.1 Read operation (basic setting) ..............19 7.2 Write operation (only DTA100, DTA200, DTA300) ........20 8 Operation ......................21 8.1 Basic settings in the AS-i network ..............21...
All manuals and user guides at all-guides.com Preliminary note This document applies to all DTA125 type units. It is part of the device and contains information about the correct handling of the product. This document is intended for specialists. These specialists are people who are qualified by their training and their experience to see risks and to avoid possible hazards that may be caused during operation or maintenance of the device.
All manuals and user guides at all-guides.com Radio equipment In general, radio equipment must not be used in the vicinity of petrol stations, fuel depots, chemical plants or blasting operations. ► Do not transport and store any flammable gases, liquids or explosive substances near the unit.
All manuals and user guides at all-guides.com function (example read/write head DTA100 and ID tag E80301) Type overview DTA10x DTA20x DTA30x Art. no. Function Type designation H x V x D [mm] DTA100 Read/write head DTS125 AARWASUS 55 x 24 x 41 DTA101 Read head DTS125 AAROASUS...
All manuals and user guides at all-guides.com Art. no. Function Type designation H x V x D [mm] DTA300 Read/write head DTS125 DCRWASUS 92 X 80 X 40 DTA301 Read head DTS125 DCROASUS Installation General installation instructions When mounting several read/write heads adhere to the minimum distances between the systems.
All manuals and user guides at all-guides.com DTA10x 5.3.1 Fixing ► The device is fixed via either 2 M4 screws and nuts or via an angle bracket. mounting example E20898 mounting example E20901 5.3.2 Mounting distances Operating mode Distance side (A) Distance front (B) Reading only ≥...
All manuals and user guides at all-guides.com 5.3.3 Positioning of the ID tags front side overhead 5.3.4 Orientation of the ID tags DTA10x antenna axis = ID tag axis DTA10x middle of the antenna = middle of the ID tag...
All manuals and user guides at all-guides.com 5.3.5 Read/write distances ID tag Type Positioning Read Write E80301 front side E80302 5...20 E80311 E80312 5...20 E80317 10...28 E80318 15...40 overhead E80319 20...60 20...50 E80320 18...60 E80322 15...40 All indications apply to static read/write operations. If not otherwise stated they refer to ID tag installation in a non-metallic environment.
All manuals and user guides at all-guides.com 5.4.2 Alignment of the sensing face 180° 90° Loosen the screw. Remove the antenna head from the fixing element and turn it. Attach the fixing element to the antenna Tighten the screw. head. 5.4.3 Fixing ►...
All manuals and user guides at all-guides.com 5.4.4 Mounting distances Operating mode Distance side (A) Distance front (B) Reading only ≥ 150 mm ≥ 150 mm For reading and writing ≥ 300 mm ≥ 300 mm 5.4.5 Positioning of the ID tags E80311 E80312 E80317 E80318 E80319 E80322 E80320...
All manuals and user guides at all-guides.com 5.4.6 Orientation of the ID tags antenna axis DTA20x = ID tag axis middle of the antenna DTA20x = middle of the ID tag 5.4.7 Read/write distances Installation read/write head ID tag Type Non flush Flush in metal E80311...
All manuals and user guides at all-guides.com DTA30x 5.5.1 Fixing ► The device is fixed via either a 35 mm DIN rail or via 4 M5 screws and nuts. example mounting E11122 5.5.2 Mounting distances Operating mode Distance side (A) Distance front (B) Reading only ≥...
All manuals and user guides at all-guides.com 5.5.3 Positioning of the ID tags E80311 E80312 E80317 E80318 E80319 E80322 E80320 front side 5.5.4 Orientation of the ID tags DTA30x antenna axis = ID tag axis DTA30x middle of the antenna = middle of the ID tag 5.5.5 Read/write distances ID tag...
All manuals and user guides at all-guides.com ID tag Type Read Write E80319 E80320 E80322 All indications apply to static read/write operations. If not otherwise stated they refer to ID tag installation in a non-metallic environment. All indications in mm. 5.5.6 Rotating plug insert The plug insert can be rotated in steps of 45°.
All manuals and user guides at all-guides.com Electrical connection Wiring ► Connect the unit to the AS-i network using the M12 connector. Voltage is supplied via the AS-i network. ASI+ Wiring and core colours of ifm sockets 1 = BN (brown) 2 = BU (blue) A selection of sockets is available on our website at: →...
All manuals and user guides at all-guides.com UL approval The following note applies to the units DTA20x and DTA30x only. ► The device shall be supplied from an isolating transformer having a secondary Listed fuse rated either a) max 5 amps for voltages 0...20 V (0...28.3 V ) or b) 100/V...
All manuals and user guides at all-guides.com Write operation (only DTA100, DTA200, DTA300) Status Description green/red ON/OFF like read operation yellow ON (pulse) ID tag written successfully no ID tag in the field or faulty ID tag in the field or invalid ID tag (wrong identification) yellow 500 ms flashing...
All manuals and user guides at all-guides.com Operation Basic settings in the AS-i network Parameter Read/write head Read head DTA100, DTA200, DTA101, DTA201, DTA300 DTA301 AS-i profile I/O code ID code Extended ID2 code ID1 code for code value Slave address (factory setting) Code values in hex format Addressing The read/write head is addressed using an addressing unit (e.g.
All manuals and user guides at all-guides.com Code value representation using the data bits D16...D1 The ID value is represented as a signed 16-bit number. Range Decimal from from Value range 32767 7FFF Message range -32768 FFFF 8000 Value 0 = no ID tag in the reading range or ID tag not detected Additional functions to the AS-i profile 7.4 (Applies only to read/write heads) Function, description...
All manuals and user guides at all-guides.com DTA30x All indications in mm Technical data The data sheets are available on our website at: → Data sheet direct → e.g. DTA100 www.ifm.com Maintenance, repair and disposal ► Do not open the housing, as the device does not contain any components which must be maintained by the user.
All manuals and user guides at all-guides.com 12.1.3 FCC Notices (USA, Canada) This device complies with Part 15 of the FCC Rules and with RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1) this device must not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
All manuals and user guides at all-guides.com 12.1.5 Singapore Complies with IDA Standards Db 103032 The “Equipment Registration” is available on our website at: → Data sheet direct → e.g. DTA100 → Approvals www.ifm.com 12.2 EC Declaration of Conformity You can find the EC declaration of conformity on our website at: →...
Seite 53
All manuals and user guides at all-guides.com...
Seite 54
All manuals and user guides at all-guides.com Inhalt 1 Remarque préliminaire ..................4 1.1 Symboles utilisés ..................4 2 Consignes de sécurité ..................4 2.1 Général ......................4 2.2 Equipements radio ..................5 2.3 Perturbations d'appareils électroniques et médicaux ........5 3 Fonctionnement et caractéristiques ..............5 4 Fonction .......................5 4.1 Principe de fonctionnement ................5 4.2 Aperçu des types ..................6...
Seite 55
All manuals and user guides at all-guides.com 6 Raccordement électrique ...................17 6.1 Schéma de branchement ................17 6.2 Distance minimale entre le câble AS-i et le boîtier ........17 6.2.1 DTA10x ....................17 6.2.2 DTA20x ....................18 6.2.3 DTA30x ....................18 6.3 Homologation UL ..................19 7 Eléments de visualisation ..................19 7.1 Fonctionnement lecture (réglage de base) ..........19 7.2 Fonctionnement écriture (uniquement DTA100, DTA200 et DTA300) ..20...
All manuals and user guides at all-guides.com Remarque préliminaire Ce document s'applique à tous les appareils DTS125. Il fait partie de l'appareil et fournit des informations sur l'utilisation correcte du produit. Ce document s'adresse à des personnes compétentes. Ce sont des personnes qui sont capables - grâce à...
All manuals and user guides at all-guides.com pour la sécurité des personnes et des installations. Elles ne sont pas autorisées et aboutissent à une exclusion de responsabilité et de garantie. Equipements radio En général, les équipements radio ne doivent pas être utilisés à proximité de stations d'essence, de dépôts de carburants, d'usines chimiques ou de lieux où...
All manuals and user guides at all-guides.com Fonctionnement (exemple tête de lecture/écriture DTA100 et TAG E80301) Aperçu des types DTA10x DTA20x DTA30x Référence Fonction Désignation H x L x P [mm] DTA100 tête de lecture/écriture DTS125 AARWASUS 55 x 24 x 41 DTA101 tête de lecture DTS125 AAROASUS...
All manuals and user guides at all-guides.com Référence Fonction Désignation H x L x P [mm] DTA300 tête de lecture/écriture DTS125 DCRWASUS 92 x 80 x 40 DTA301 tête de lecture DTS125 DCROASUS Montage Notices de montage générales En cas de montage de plusieurs systèmes respecter les distances minima- les entre les tètes de lecture/écriture .
All manuals and user guides at all-guides.com DTA10x 5.3.1 Fixation ► La fixation se fait par 2 vis M4 et écrous ou par une équerre. exemple de montage E20898 exemple de montage E20901 5.3.2 Distances de montage Mode de fonctionnement Distance latérale (A) Distance frontale (B) Seulement lecture...
All manuals and user guides at all-guides.com 5.3.3 Positionnement des TAG face avant au dessus de la tête 5.3.4 L'orientation des TAG axe de l'antenne DTA10x = axe du TAG milieu de l'antenne DTA10x = milieu du TAG...
All manuals and user guides at all-guides.com 5.3.5 Distances de lecture/écriture Type Positionnement Lecture Ecriture E80301 face avant E80302 5...20 E80311 E80312 5...20 E80317 10...28 E80318 15...40 au dessus de la tête E80319 20...60 20...50 E80320 18...60 E80322 15...40 Toutes les indications s'appliquent à des process lecture/écriture statiques. Sauf indications contraires, elles se réfèrent au montage du TAG dans un environnement non-métallique.
All manuals and user guides at all-guides.com 5.4.2 Orientation de la face active 180° 90° Desserrer la vis. Séparer la tête d'antenne de l'accessoire de fixation et la tourner. Placer l'accessoire de fixation sur la tête Serrer la vis. d'antenne. 5.4.3 Fixation ►...
All manuals and user guides at all-guides.com 5.4.4 Distances de montage Mode de fonctionnement Distance latérale (A) Distance frontale (B) Seulement lecture ≥ 150 mm ≥150 mm Lecture et écriture ≥ 300 mm ≥ 300 mm 5.4.5 Positionnement des TAG E80311 E80312 E80317 E80318 E80319 E80322 E80320...
All manuals and user guides at all-guides.com 5.4.6 L'orientation des TAG axe de l'antenne DTA20x = axe du TAG milieu de l'antenne TA20x = milieu du TAG 5.4.7 Distances de lecture/écriture Montage de la tête de lecture/écriture Encastré dans le Type Non encastré...
All manuals and user guides at all-guides.com DTA30x 5.5.1 Fixation ► La fixation se fait sur rail 35 mm ou par 4 vis et écrous M5. Exemple de montage E11122 5.5.2 Distances de montage Mode de fonctionnement Distance latérale (A) Distance frontale (B) Seulement lecture ≥...
All manuals and user guides at all-guides.com 5.5.3 Positionnement des TAG E80311 E80312 E80317 E80318 E80319 E80322 E80320 face avant 5.5.4 L'orientation des TAG axe de l'antenne DTA30x = axe du TAG milieu de l'antenne TA30x = milieu du TAG 5.5.5 Distances de lecture/écriture Type...
All manuals and user guides at all-guides.com Type Lecture Ecriture E80319 E80320 E80322 Toutes les indications s'appliquent à des process lecture/écriture statique. Sauf indications contraires, elles se réfèrent au montage du TAG dans un environnement non-métallique. Toutes les indications en mm. 5.5.6 Orienter l'insert du connecteur L'insert du connecteur est orientable en pas de 45°.
All manuals and user guides at all-guides.com Raccordement électrique Schéma de branchement ► Raccorder la tête de lecture/écriture au réseau AS-i via le connecteur M12. L'alimentation en tension s'effectue via le réseau AS-i. ASI+ Schéma de branchement et couleurs des fils conducteurs des connecteurs femelles ifm 1 = BN (brun) 2 = BU (bleu) Une sélection de connecteurs femelles est disponible sur notre site web à...
All manuals and user guides at all-guides.com Homologation UL La remarque suivante ne s‘applique qu‘aux appareils DTA20x et DTA30x. ► L‘appareil doit être impérativement alimenté par une alimentation isolée galvaniquement disposant au secondaire d‘un fusible avec homologation UL et un courant nominal max. de a) 5 ampères pour des tensions de 0...20 Veff (0...28.3 Vpic) ou b) 100/Vpic pour des tensions de 20...30 Veff (28.3...42.4 Vpic).
All manuals and user guides at all-guides.com Fonctionnement écriture (uniquement DTA100, DTA200 et DTA300) Etat Signification verte/ ALLUMEE/ETEINTE comme fonctionnement lecture rouge jaune ALLUMEE (impulsion) TAG écrit avec succès ETEINTE aucun TAG dans le champ ou TAG défectueux dans le champ ou TAG non valable (identification incorrecte) jaune 500 ms clignotant...
All manuals and user guides at all-guides.com Représentation des valeurs analogiques Pour l'AS-interface la tête de lecture/écriture est un esclave ayant une entrée analogique avec le protocole de transmission selon le profil 7.4 ou 7.3 (voir ci-dessus). Si le maître travaille selon le profil maître M3 ou M4, il détecte automatiquement la tête de lecture/écriture et est compatible avec le profil 7.4.
All manuals and user guides at all-guides.com Fonctions supplémentaires selon le profil AS-i 7.4 (S'appliquent seulement aux têtes de lecture/écriture) Fonctionnement, description DTA100 DTA200 DTA300 Read ID string (lecture de la chaîne ID) Vérifier les informations esclave AS-i ● ● ●...
All manuals and user guides at all-guides.com DTA30x Toutes les indications en mm. Données techniques Les fiches techniques sont disponibles sur notre site web à : → Fiche technique → par ex. DTA100 www.ifm.com Maintenance, réparation et élimination ► Ne pas ouvrir l'appareil car il ne contient pas de composants à maintenir par l'utilisateur.
Attention: Tout changement ou modification effectué sans autorisation explicite de la part d'ifm electronic gmbh peut entraîner l'annulation de l'autorisation de la part de FCC d'utiliser ces appareils. Remarque : Cet appareil a été testé et est conforme aux limites concernant les dispositifs numériques de classe B selon la partie 15 des règlements FCC.
All manuals and user guides at all-guides.com 12.1.5 Singapour Complies with IDA Standards Db 103032 Le "Equipment Registration" est disponible sur notre site web à : → Fiche technique → par ex. DTA100 → Homologations www.ifm.com 12.2 Déclaration de conformité CE La déclaration de conformité...
Seite 79
All manuals and user guides at all-guides.com...