x-pulse XP600.4 Bedienungsanleitung Seite 23

Ne2 XP6004/7005/8001 RZ (D+UK)
should be a fullrange (unfiltered) signal, in case the
integrated lowpass crossover shall be used!
6
SUBWOOFER OUTPUT TERMINAL
Speaker terminal to connect the positive ("+") and
negative ("-") speaker wires of the subwoofer to the
amplifier. The load impedance of the connected sub-
woofer system may vary between 1 to 4 ohms!
7
SPEAKER OUTPUT TERMINAL 3-CH&4-CH
Speaker terminal to connect the positive ("+") and
negative ("-") speaker wires of channels 3&4-CH to
the amplifier. Note: The positive ("+") terminal of
channel 3-CH and the negative ("-") terminal of chan-
nel 4-CH provide the bridged output of the channel
pair 3-CH&4-CH! The load impedance may vary bet-
ween 1 to 4 ohms per channel, or – consequently - 2
to 4 ohms in bridged operation mode.
8
SPEAKER OUTPUT TERMINAL 1-CH&2-CH
Speaker terminal to connect the positive ("+") and
negative ("-") speaker wires of channels 1&2-CH to
the amplifier. Note: The positive ("+") terminal of
channel 1-CH and the negative ("-") terminal of chan-
nel 2-CH provide the bridged output of the channel
pair 1-CH&2-CH! The load impedance may vary bet-
ween 1 to 4 ohms per channel, or – consequently - 2
to 4 ohms in bridged operation mode.
9
GND Power terminal for the connection of the
amplifier to the chassis ground or the negative pole of
the car battery.
10
REM Remote terminal (switching contact) for the
automatic (remote) turn-on / turn-off of the power
amplifier from the head-unit's remote lead (or antenna
control lead).
11
BATT +12V + 12 V power terminal for the
connection of the amplifier to the positive pole of the
car battery.
12
FUSE Internal fuses, 2 x 30 Ampere ATC to protect
the power supply circuitry of the XP700.5 amplifier.
13
Phase shift knob to adjust the
PHASE SHIFT
absolute phase of the amplified subwoofer out-
put signal. Used to match the phase of the front
satellite speaker systems to the subwoofer.
14
LOW PASS Lowpass frequency control knob to
adjust the integrated 12 dB/oct. lowpass filter of the
subwoofer channel. Allows the setting of the required
lowpass frequency between 35 Hz and 200 Hz.
15
SUBSONIC Subsonic frequency control knob to
adjust the integrated 12 dB/oct. subsonic highpass fil-
16.08.2000 6:32 PM
ter of the subwoofer channel. Allows the setting of
the desired highpass frequency between 10 Hz and 50
Hz. The subsonic highpass filtering of the sub channel
can not be defeated!
16
5-CH (SUB) LEVEL Input gain adjustment knob to
adjust/match the input gain of the subwoofer channel
to the incoming signal from the head unit. The input
level stage accepts input voltages between 0,2V to 9V.
17
3&4-CH LEVEL Input gain adjustment knob to
adjust/match the input gain of channel 3&4-CH to the
incoming signal from the head unit. The input level
stage accepts input voltages between 0,2V to 9V.
18
HIGH PASS Highpass frequency control knob to
adjust the integrated 12 dB/oct. highpass filter of
channel 3&4-CH, when the slide-switch of the 3&4-CH
X-OVER is set to HP (highpass) mode. Allows the set-
ting of the required highpass frequency between 40
Hz and 200 Hz.
19
3&4-CH X-OVER Input mode selector of the inte-
grated active crossover, controlling the channels 3&4-
CH. The slide switch allows to set the crossover of
channel 3&4-CH to highpass (HP), fullrange (FULL), or
bandpass (BP) operating mode.
20
LOW PASS Lowpass frequency control knob to
adjust the integrated 12 dB/oct. lowpass filter of
channel 3&4-CH, when the slide-switch of 3&4-CH
X-OVER is set to BP (bandpass) mode. Allows the set-
ting of the required lowpass frequency between 35 Hz
and 200 Hz.
21
HIGH PASS Highpass frequency control knob to
adjust the integrated 12 dB/oct. highpass filter of
channel 1&2-CH, when the slide-switch of 1&2-CH
X-OVER is set to HP (highpass) mode . Allows the set-
ting of the required highpass frequency between
40 Hz and 400 Hz.
22
1&2-CH X-OVER Input mode selector of the inte-
grated active crossover, controlling the channels 1&2-
CH. The slide switch allows to set the crossover of
channel 1&2-CH to highpass (HP), or fullrange (FULL)
operating mode.
23
1-CH&2-CH LEVEL Input gain adjustment knob to
adjust/ match the input gain of channel 1-CH&2-CH to
the incoming signal from the head unit. The input level
stage accepts input voltages between 0,2V to 9V.
24
INPUT MODE Input mode selector switch, allo-
wing this amplifier being driven by either one, two or
three pairs of stereo line signals from the head-unit
and the corresponding RCA interconnect cables.
Seite 23
23