Werbung
Verfügbare Sprachen
Verfügbare Sprachen
US
Information for use
sera LED Digital Dimmer
Please read these instructions carefully and keep for future use. When forwarding this unit to third
parties, this information for use is also to be handed over.
The sera LED Digital Dimmer is a controller for pro-
gramming sera LED lighting appliances such as the
sera LED X-Change Tubes, sera LED aquariums
and the sera LED lights. You can adjust maximum
brightness and use the dimmer as a time clock. Com-
bination with the sera LED X-Change sunrise Tubes
and some of the sera LED Chips even allows simu-
lating sunrise and sunset in combination with 2 dif-
ferent cloud scenarios as desired. In case of the sera
LED X-Change cool daylight Tubes and other sera
LED products, dimming does not alter the light col-
or but only changes the brightness. Cloud simulation
by the sera LED Digital Dimmer is possible with all
LED tubes.
SAFETY PRECAUTION
Use the sera LED Digital Dimmer only as described
in this information for use. It is a low voltage dimmer
for a range of 10 – 20 V DC. The maximum current
on the input side should not exceed 3 A. Maximum
input voltage cannot exceed the output voltage.
Application
The brightness of the lamps connected to the Digital
Dimmer increases or decreases in pre-programmed
steps. Adjustment can be done either automatically
or manually.
Application range
The sera LED Digital Dimmer can be used in a ver-
satile way and allows controlling the sera LED
X-Chan ge Tubes as well as the sera LED aquariums
and sera LED lights.
sera LED X-Change System
The sera LED Digital Dimmer allows operating one
or more sera LED X-Change Tubes (also different
lengths) up to a total of 60 W.
sera LED aquariums
All sera LED aquariums such as the marin Biotop
LED Cube 130, the Biotop LED Cube 130 XXL, the
Biotop Nano LED Cube 60 and the Biotop Nano LED
Cube 16 can be operated and programmed with the
sera LED Digital Dimmer.
sera LED lamps
The sera Nano LED light and the sera LED light,
both equipped with sera LED Chips, can be con-
nected solely or combined with more units by the
sera LED Triple Cable, and can be programmed with
a single sera LED Digital Dimmer.
When connecting several lamps/units of the same
voltage (for example do not combine 12 V and 20 V
lamps, but only 12 V and 12 V or 20 V and 20 V), it
is necessary to choose a suitable electronic bal -
last. Make sure the output voltages of the ballast and
the operating ranges of the LED lamps are identi -
cal. For instance, never connect a 12 V LED lamp to
a 20 V ballast. Warranty of the devices will be void in
case of damage as consequence of inappropriate
use.
When the sera LED Digital Dimmer is used with oth-
er LED lamps or illuminating light units, make sure
that the maximum current flow is not exceeded, and
that the lamps are really dimmable in the range of
10 – 20 V. Several LED lamps can be connected to
one ballast.
Kit includes (1)
sera LED Digital Dimmer with cable and
1.1
5.5 mm barrel connectors
1.1.1 display
1.1.2 HOUR, F1 – F4, DEMO key
1.1.3 MINUTE, ON/OFF, RESET key
1.1.4 MINUS key
1.1.5 PLUS key
1.1.6 SET key
1.2
holder
1.3
screws (4 pieces)
Assembly instruction
The sera LED Digital Dimmer should be connected
between ballast and LED lamp. Should you intend to
control more than one light unit, please connect the
sera LED Triple Cable to the outlet connector of the
dimmer. By adding more triple cables you can even
attach more appliances. The barrel connectors of the
cables do not allow confusion, and polarity reversion
cannot occur.
7
Werbung
