Overload Protector - Makita CA5000 Betriebsanleitung

Adjusting depth of cut
To adjust depth of cut, turn the depth adjusting knob.
For deeper cut, turn it clockwise. For shallower cut, turn
it counterclockwise.
► Fig.8: 1. Depth adjusting knob
Sighting
Triangular mark on the base indicates the center of the
groove cutter blade.
When using with groove cutter blade, align the outside
triangular mark with the cutting line.
When using with circular saw blade (optional accessory),
align the inside triangular mark with the cutting line.
► Fig.9: 1. Base 2. Outside triangular mark 3. Inside
triangular mark 4. Cutting line
Switch action
CAUTION:
Before plugging in the tool, always
check to see that the switch trigger actuates
properly and returns to the "OFF" position when
released.
To prevent the switch trigger from being accidentally
pulled, a lock-off button is provided.
To start the tool, push in the lock-off button and pull the
switch trigger.
Release the switch trigger to stop.
► Fig.10: 1. Lock-off button 2. Switch trigger
Speed adjusting dial
CAUTION:
The speed adjusting dial is not for
using low speed rated blades but for obtaining a
speed which is suitable to material of workpiece.
Use only blades which are rated for at least the maxi-
mum no load speed stated in the SPECIFICATIONS.
CAUTION:
The speed adjusting dial can be
turned only as far as 6 and back to 1. Do not force it
past 6 or 1, or the speed adjusting function may
no longer work.
The tool speed can be adjusted by turning the adjusting
dial. Higher speed is obtained when the dial is turned in
the direction of number 6; lower speed is obtained when
it is turned in the direction of number 1.
Refer to the table to select the proper speed for the
workpiece to be cut. However, the appropriate speed
may differ with the type or thickness of the workpiece. In
general, higher speeds will allow you to cut workpieces
faster but the service life of the blade will be reduced.
Number
1
2
3
4
5
6
► Fig.11: 1. Speed adjusting dial
Guide plate
For aligning the guide rail (optional accessory) with the
cutting line, use the guide plate.
► Fig.12: 1. Guide plate 2. Plate edge 3. Cutting line
1.
the cutting start point. The plate edge represents the
center of the groove cutter blade. Align the plate edge
with the cutting line.
2.
near the cutting end point. And align the plate edge with
the cutting line again.
Other features
The tools equipped with electronic function are easy to
operate because of the following features.

Overload protector

When the load on the tool exceeds admissible levels,
power to the motor is reduced to protect the motor from
overheating. When the load returns to admissible lev-
els, the tool will operate as normal.
Constant speed control
Electronic speed control for obtaining constant speed.
Possible to get fine finish, because the rotating speed is
kept constant even under load condition.
Soft start feature
Soft start because of suppressed starting shock.
ASSEMBLY
switched off and unplugged before carrying out
any work on the tool.
Hex wrench storage
Hex wrench is stored on the tool. To remove hex
wrench, just pull it out.
To install hex wrench, place it on the grip and insert it as
far as it goes.
► Fig.13: 1. Hex wrench
Removing or installing groove
cutter blade
-1
min
2,200
with the characteristics specified in these instructions.
2,700
3,800
for at least the maximum no load speed stated in
the SPECIFICATIONS.
4,900
6,000
teeth pointing up at the front of the tool.
6,400
install or remove the blade.
9 ENGLISH
Set the guide plate onto the guide rail near from
Then, set again the guide plate on the guide rail
CAUTION:
Always be sure that the tool is
CAUTION:
Do not use blades which do not comply
CAUTION:
Use only blades which are rated
CAUTION:
Be sure the blade is installed with
CAUTION:
Use only the Makita wrench to